KL-MI-BP plastic melt indexer

The melt flow rate instrument is different from other domestic manufacturers the advantages of a melt flow rate instrument: a heated cylinder 304 stainless steel or alloy production, due to the melt flow rate meter long at high temperatures (up to 400 to 500 degrees). metal material easily oxidized at high temperatures rust 3, two sensor configuration, precise temperature control, temperature gradient better and live longer 4, according to the national standard, four minutes after the addition increase countdown function 5, RS232 interface, can be directly connected to the computer output data (optional) 6, the boot can directly display the last test conditions are reset each time the user avoid test parameters, reducing operator workload 7, the highest temperature can reach 450 to 500 degrees (optional, when ordering special Description) 8, can be tested for a long time without compromising corrosive plastic precision instrument, such as a full line of fluorine plastic (due to special materials, please specify when ordering) so the whole type fluorine plastic (due to special materials, please specify when ordering), the only domestic Kunlun detection equipment 9 companies have this technology, to meet the standards: ISO 1133, ASTM D1238, GB / T3682 I. Model: KL-MI-BP Second, the product description: Kunlun melt flow rate tester for the improved models, increasing the number of function, the instrument configuration, instrument service life, ease of operation, test accuracy has greatly improved, with the domestic general a melt flow rate instrument the incomparable advantages and cost effectiveness. Third, to meet the standards: ISO 1133, ASTM D1238, GB / T3682 Fourth, the product uses: for the determination of a variety of plastic, resin melt flow rate MFR value when the viscous flow state, applicable both to the higher melting temperature polycarbonate esters, polyaryl sulfone, fluorine plastic, nylon and other engineering plastics, are also suitable for polyethylene (PE), polystyrene (PS), polypropylene (PP), ABS resin, polyoxymethylene (POM), polycarbonate (PC ) low melting temperature of the plastic resins and other tests, widely used in plastics production, plastics, petroleum and chemical industries as well as relevant institutions, research institutes, and commodity inspection departments. It applies to "GB / T3682-2000 thermoplastic melt flow rate and melt volume flow rate measuring" the national standard in measuring the flow rate of melt indexer provisions of thermoplastic melt quality, this is equivalent to using the ISO 1133 standard : 1997 requirements, and can meet the ASTM D1238 test standard. MFR rate instrument for the desktop structure, stable and reliable performance and reasonable design, beautiful appearance, convenient operation, using high-performance, high-precision control instruments with high sampling accuracy, control the rate and fast, using the fuzzy PID algorithm temperature control. V. Features: 1, heating speed, small overshoot 2, high temperature accuracy 3, after filling, constant temperature can be restored quickly 4, the test parameter calibration and correction convenient 5, can be manual, automatic cut material test The method, Chinese liquid crystal display 7, equipped with a printer, the test results are automatically printed output 6, the main technical parameters 1, the extruded material portion of the discharge diameter: Φ2.095 ± 0.005 mm spout length: 8.000 ± 0.025 mm loading cartridge diameter: Φ9.550 ± 0.025 mm, loading cartridge length: 152 ± 0.1 毫米 piston head diameter: 9.475 ± 0.015 mm and a piston rod head length: 6.350 ± 0.100 mm2, standard test load (Total 8 a full set of weights) 3, temperature range: Standard room --400 ℃ (500 ℃ optional) 4, temperature accuracy: ± 0.5 ℃ 5, the display resolution: 0.1 ℃ 6, cut material way: Optional manual or automatic cut material 7, the temperature recovery time: less than 4 minutes 8, print: mini-printer to automatically print out 9, the power supply voltage: AC220V ± 10% 50HZ