Atomizer

Air atomizing nozzles, air and water mixing atomizing nozzle, water aerosolization nozzle, curing chamber nozzle, humidification nozzle, Air water nozzle, water nozzle, air nozzle / nozzle, the nozzle cross www.ktyco.com air mist nozzles 7000 of nozzle air flow and liquid flow affect each other and produce a fine mist of device, the device special internal structure design enables uniform mixing of liquids and gases, producing fine or coarse spray droplet size of a spray of droplets. Typically, by increasing the gas pressure or hydraulic pressure available to reduce the more fine spray droplets, resulting in higher gas flow rate than the liquid flow rate. 7000 series adjustable air atomizing nozzle capable of regulating the liquid flow, without changing the air pressure and the liquid pressure of the environment, can also be desirable to produce a spray, and therefore highly adaptable. Each spray device by the air cap and fluid wool, with the ability to provide a fan and round spray pattern, and has a wide range of flow rates. Inlet fitting nozzle body has a variety of sizes, most commonly used for piping. Interchangeable nozzle assembly above, which provides for the flexibility of the obtained different spray performance. General Application: Spray humidification; die lubrication; spray additives; air disinfection; fresh fruits and vegetables; wool spray humidifier; greenhouse thermostat; Model: 7000 Series Specifications: 1/4 Material: Stainless Steel Installation Type: internal thread Working pressure: 0.7 -35 Mpa Working temperature: -50-300 ℃ Medium: water, acid and alkali liquid Application: Spray humidification; die lubrication; additive fuel injector spray Description: Fuel nozzle for fog-generation fuel injectors after several such improvements, dimensions, nominal, and oil network has been optimized, improved, in line with European standards CEN to install itself and ignition electrodes are easily available with different spray angle nozzles:. a, in accordance with CEN standards in the four Species spray mode with 60 degrees, 70 degrees, 80 degrees, 90 degrees, 100 degrees five spray angles I, II, III, IV, V lower. b, according to the current non-European standards, fuel injectors have 30 degrees, 45 degrees, 60 degrees, 80 degrees, four kinds of spray angle and S (solid), H (hollow) and B (semi-solid) three spray. www.ktyco.com Nozzle Type: Specification: 1/4 Material: Stainless steel, Brass Installation Type: External thread Working pressure: 0.3-50 Mpa Working temperature: -50-300 ℃ Medium: water, oil scope of application: low pressure injection fine atomizing nozzle Description: Low fine atomizing nozzles, landscaping sprinklers, fog nozzles, fine atomizing nozzle 7004 series of low-fine atomizing nozzles using glass fiber reinforced polypropylene plastic, all the components of precision manufacturing, spray mist slight drop. Nozzle with internal filter, clogging, largely extended service life. www.ktyco.com nozzle general application: plant cooling; greenhouse thermostat; landscape-made fog Model: 7004 Specification: 1/8 Material: Plastic Installation Type: External thread Working pressure: 0.2-14 Mpa Working temperature: 0-50 ℃ Medium: Water Scope: plant cooling; greenhouse thermostat; landscape-made fog high pressure fine spray nozzles Description: High fine atomizing nozzles, anti-drip fine atomizing nozzles, fine atomizing nozzle 7004 series of anti-Dettol fine mist nozzle design principle of high-speed flow of liquid under 70kg-120kg pressure, to form a centrifugal swirl in the guide vanes, the discharge and fine grain hollow-type mist from the spray holes. Teflon filters, orifices are using high-precision punching mechanism into the United States, between the aperture in 01.mm-0.6mm, well-made. Kind of nozzle is widely used in factories humidification, salt spray test, artificial fog and other wet places. Two materials with stainless steel and brass. www.ktyco.com nozzle general application: air humidification; flue evaporative cooling; chemical treatment; liquid spray; tablet coating; plant humidification; sterilization; spray wax fruit; other places humidification; Model: 7004 Series Specifications: 1/8 Material: Stainless steel, Brass Mounting Type: Threaded Working pressure: 0.2-14 Mpa Working temperature: -50-300 ℃ media: Water Scope: air humidification; flue evaporative cooling season just nozzles Description: Race just nozzles, PVDF Race steel nozzle pressure nozzle at 7kg temperature-resistant up to 148 ℃, ideally suited for printed circuit board (PCB) manufacture development, rinsing, plating, etching, in addition to film production process. PVDF is a natural, non-pigmented high purity material, race steel nozzle that is made by the PVDF, thus maintaining a high degree of purification process is also environment, particularly suited for the production of ultra-pure process. PVDF has excellent chemical anti-corrosion properties, it is possible to effectively spray all kinds of chlorides, excellent acid group, base, or amine etchant, anti-aging properties. PVDF is a high-hard materials, high mechanical strength, wear resistance, impact resistance. Such nozzle 1/8 ", 1/4" and 3/8 "three Connector size, suitable for most common pipe, and provide different angles jet flow to meet the diverse needs of .www.ktyco.com nozzle General Application: Printed circuit board production; washing and bleaching cream; dust, gas scrubbing; quenching and cooling; oxygen, degassing, ventilation; Model: 6100 Series Specifications: 1/8, 1 / 4,3 / 8 Material : PVDF Mounting: Threaded Working pressure: 0.2-14 Mpa Working temperature: 0-50 ℃ Medium: water, acid and alkali liquid Scope: Printed circuit board production; washing and bleaching cream