Au Mongolia Asia exclusive ice liquid

TBS-310 Operating Instructions - etched ice liquid ice by the concave recessed from Mongolia and Mongolia evolution, which enables faster speed concave, ice pattern brighter, deeper depression, lower cost, longer life liquid. Ice glass is the use of cartographic production of three-dimensional carving through a chemical reaction, carved beautiful patterns. It can be said is an extension of ice glass Au Mongolia glass, but glass ice than Au Mongolia glass is more effective and more with three-dimensional. Ice made of glass with a small investment, quick market response and so on. It is just a listing, much consumers of all ages and glass processing, three-dimensional Ice texture, uneven texture is clearly crafted, gods caused by crystal particles entrained in the ice patterns, like pearls strewn beach , sparkling, dazzling gorgeous, with a general pattern of ice performance, elegant and luxurious sense legislation, and the extraordinary. (1) replace sand carving-saving time, the effect is several times stronger than the sand carving, lower cost than sand carving, the price is several times higher than the sand carving. (2) substituted carved carved ten times faster than the production speed. The effect is not inferior carved. (3) it is easy to replace the car carved lines can be fine thick, brighter than the brightness of the car the moment, although no car carved smooth, far more than the three-dimensional carved out of the bus. Moreover, there are higher investment vehicle engraved equipment, technology difficult to master and other shortcomings. It also has a hot-melt characteristics. This process can also make ice crystal glass shell mask pattern. Just a minute, the ice can be used with any process technology mix, without restriction pattern. First, the process equipment 1, drug requirements for tanks and piping material or PP sheet PVC sheet material, wherein the sheet or PVC sheet PP requirements 8-12mm thickness. 2, try to seal the entire equipment requirements. Since the ice has a volatile liquid, so the combination of the cap and seal around the frame should have. 3, size, specifications according to customer requirements. Second, the operating process 1, clean: because there are certain inorganic exist on the surface of ordinary glass, so the glass dip in the pool before the application of ice on its surface was scrubbed to remove inorganic, glass, and it was soaked in acid to produce crystal clear after .. clear, smooth unblemished effect but also can improve the life of 2 ice liquid, soak: place the need to deal with both sides of the glass with a protective film to prevent acid paste from other parts of the glass corrosion, remove decorative patterns section protective film, and then the bottom of the glass facing the pool soaking into the design part of the pool (soaking the glass bottom booster 1-2cm), the ice was still soaked in syrup of 50 to 120 minutes (soaking time desired by the customer the effect of the decision; such as: corrosion of glass 1 mm depth, need to soak 30 to 50 minutes or so) the stronger the corrosive effect is usually soak longer produced, Remarks (indoor temperature is normally 35 degrees is best reaction temperature) when. After achieving satisfactory results, the glass removed from the pool, clean derived products; produce bright, full of three-dimensional lines icicles, ice glass with its production of simple, elegant artistic effect is gradually occupy a place in the market with the ordinary. carving methods can not achieve special artistic effects. Third, Au Mongolia maintain an ice syrup, syrup soaking the glass in 50 to 120 minutes, soak the length of time have a greater impact on the etch depth and fullness of icicles, long time then etched deep and profound icicles, otherwise light and delicate, so according to the requirements of the glass effect to determine the soaking time. 2, after the medicine used for some time, the concentration decreases, the etching depth is not enough, soak time may be extended, as the effect is not obvious, you should consider adding ice syrup. 3, will produce some white precipitate should be periodically cleaned out (using 600-800 mesh screen filter for syrup), otherwise it will affect icicles effect, resulting syrup white rim after a period of time. Still generate clean up after the white side of a white precipitate solutions to add 2% of the total weight of the ice syrup tap water, the liquid used to dilute the concentration of impurity ions, and then add the concentrate; such as etching effect is still good, only a small amount of white edge, then just add water, no need to add the concentrated liquid. 4. The method of adding 10% of the total drug added etchant liquid water, stir well and was aged at room temperature for about 2 hours. 5, using the process as much as possible to seal the syrup, the syrup to reduce evaporation. Fourth, note 1, the operation of the workers must wear protective clothing, boots and gloves, face masks, avoid direct skin contact with syrup. 2, the operating space to be ventilated, the operation of Chinese herbal medicines need to be sealed to prevent the volatile potion surrounding environment. 3, prior to production use small glass test results to determine the solution concentration, the etching depth and the etching time required, and then production. 4. soaking, glass etching must still face down on the pitch of 1 to 1.5㎝. The glass should be placed as far as possible to avoid air bubbles, otherwise it will affect icicles effect. To batch mode can be stacked. 5, stop production, medicine should be completely sealed, keeping efficacy. Contact: Dr Miss Contact: 13702378374