Shantou Plastic drying mixer Supply mixer Supply plastic granules

Shantou Plastic Drying Mixer Supply | plastic granules opportunities a mixer, plastic drying mixer advantages: the traditional hot air dryer is entered from the lower side of the barrel, since the material is stationary, so the hot air is difficult to penetrate, so the dryer phenomenon emerged within the lower portion of the upper temperature heat, sometimes due to local overheating occurs sintered material, causing blockage, make it more difficult to enter other areas of hot air, it can not achieve the desired drying effect. The machine is designed to transport two propellers, the first stage will feed into the barrel, and then feed the second stage did not listen to the first elevated to the upper portion of the barrel and scatter umbrella, and hot air from the lower portion of the barrel center to the surrounding blown up smoothly penetrate through the gap in the movement of raw materials, the raw material is fully heated under dynamic conditions. Second, the plastic drying mixer features: 1. one machine, stirring drying simultaneously: As the material during the drying process, continuing to maintain flow state, even heat penetration, shorten the drying time and less logistics knot fast; 2. The series Standard models are: double barrel design (economy single layer design), inner material contact parts made of stainless steel manufacturing; interlayer installation and special insulation materials, which can reach safety, energy-saving effect; 3. special high-frequency heater, heating fast, low power consumption, overall cost of raw materials dried 25-30 yuan / ton. 4. The ad hoc twin humidity mouth, can effectively remove moisture, dust collecting parts, not pollute the environment 5. The barrel is provided with an inlet door, changing color clean up quick and easy refueling; 6. special modification, this series models easily available for plastic grain powder, crystallized PET pellets of dried purposes; 7. type, large capacity, standing a performance load: 0.5 t .1 tons, 1.5 tons, 2 tons, 3 tons and other spot for customer choice ; 8. combo dry mixing function, when no drying, simply "; heating switch"; and "; fan switch"; close, can be used for plastic stirring homogenization purposes. Third, plastic drying mixer purposes: for the mixed raw material in the plastics industry plastic granules, powder, etc., so that the different plastic mixing, using gear motor, and the mixing process does not produce dissolved materials, volatile or deterioration, mainly for in: crushed material, plastic film, plastic pellet, like materials, broken materials dried by stirring. Fourth, the plastic drying mixer structural features and components: 1. whole frame, rugged, smooth operation, the stirring blade and the material contact at all with stainless steel, have good corrosion resistance, keeping quality and clean materials , without discoloration. 2. Transmission mechanism adopted means at the top of the motor barrel by belt drive screw, worm gear to drive the mixer 1:40 deceleration direct drive, no excessive noise when used, and there are enough oil reserves, to get good lubrication. 5. Each member agency made: 1, reducer line mixer of the main transmission structure, which is located at the top of the barrel by means within the plane, the shaft is hollow and is equipped with fixed keys work, make paddle free assembly and disassembly. 2, the barrel body is three-dimensional, made of stainless steel, built vertical stirring blades, set upright in the barrel body. 3, cutting reducer, driven by the device while working within the frame of the motor with a drive worm screw stirring mixer barrel is rotated clockwise, so that large one-time discharge the mixed materials. 4, member-run pieces, reducer lubricating parts are oil-immersed, its oil reserves must be held in the oil standard line, the oil must be kept clean. As often with large mixer must change once every three months, the new oil, the gear unit should be replaced after cleaning washable add new oil. Sixth, after-sales service: to create brand, enhance their visibility and establish a corporate image, our spirit of "all the pursuit of quality, customer satisfaction for the purpose of" spirit, "the most preferential prices, the most attentive service, the most reliable products the principle of quality "to your solemn promise: 1, the buyer can use the department to the Division I free equipment operation training; 2, after three months, our customer service department will use the situation of returning equipment; 3, Division I of the sale equipment, free warranty for one year warranty, spare parts and maintenance are provided free; however, all the non-normal damage to equipment not covered under warranty, the buyer shall pay the cost of replacement parts. 4, outside the warranty period, when the damage must pay the cost of parts (press material procurement cost.) The replacement; 5, received a customer calls and "equipment failure notice", the through remote maintenance, such as not maintaining Guangdong range within 24 hours of arrival in the scene, arriving within 72 hours outside Guangdong scene; 6, you can simply dial the telephone or otherwise contact us, we will solve your technical issues task.