Copper wire drawing oil, copper wire drawing oil, cleaning agents

 Processing copper wire drawing oil products waste processing 6 copper wire drawing oil waste including breaking and water purification steps. Demulsification mainly to the two-phase separation of oil and water, the principle is added to the emulsion containing Ca2 +, Na +, salts of the compounds of Al3 + and other metal ions, so that the emulsion of a surfactant thereto to form insoluble soaps, thus creating cohesion. In the use of sodium chloride and potassium aluminum sulfate being preferred. follows first emulsion into 2m3 or 3m3 of waste production tank, the PH value is adjusted to 6.5 to 7.5, the amount of the waste liquid was added 2% to 5% sodium chloride, after stirring to melt 2h, then add 1% to 3% of the amount of waste aluminum potassium sulfate, stirred until dissolution, still 24h, wait until the condensation stratification, the lower part of the release of wastewater, chemical oxygen demand (COD) and oil content should be less than the national emission standards on the part of the cohesion to do things by the separation of fuel treatment. This Treatment of low-cost copper wire drawing oil Changzhou, not only to achieve the purpose of water purification, but also recycling, reduce production costs, reduce environmental pollution, and to get some money. drawing oil is used for drawing, drawing process efficient lubricant, specifically for the following areas: 1, all kinds of wire, wire La Sila line process; 2, electronic components lead copper clad steel wire, bronze-plated bead wire, copper wire drawing process; 3, smooth wire drawing. Drawing oil must then be placed in the use of one-third of the water in the tank, pour into the desired fuel consumption, recycling stir, add water to the desired amount and concentration, you can get high-quality copper wire drawing liquid After annealing wire beautiful luster, helps dry enameled other secondary processing. to eliminate static from and attached to the cleaning agent after the pumping line Longgang copper powder, copper kept clean. Drawing less demanding on the quality of the oil is in the boiling temperature, it will not break the rubbish SX-801 emulsion stability, chop to stretch the line was aging. has a special anti-rust agent, make copper stretch after pumping to maintain long-term bright surface. emulsifier drawing oil from hydrophilic groups and lipophilic groups of two parts, to maintain the stability of the emulsion, the crucial role of emulsifier. Drawing oil also has a copper wire to prevent oxidation, non-stick line, cleaning, non-foam, non-toxic, stable physical and chemical properties. 5. Maintenance and control emulsion emulsion maintenance during use properly managed, not only get the best processing results, and can greatly extend the life of the emulsion, reducing waste emissions cleaner Shenzhen, resulting in the largest economy effectiveness, maintenance and management of the emulsion has two aspects, one is to prevent mixing of the outside world and the timely removal of contaminants, and the other is to maintain stable performance water-based fluid: such concentration, rust resistance, PH, antibacterial capability. the concentration of the emulsion should be controlled within a prescribed range, in order to ensure a variety of properties to meet the requirements. Determination of the concentration of available refractometer, the oil content of the emulsion measured or a specific component or a particular (e.g. base value, the alcohol amine content), etc. method by measuring the concentration determined after a period of time is required to use additional water or additional concentrates. PH value of the emulsion in the course will usually be reduced values ??decline .PH emulsion can cause rust resistance, antibacterial worse. When the concentration meets the requirements, PH value was less than the required value, should be timely and PH value of copper wire drawing oil, triethanolamine, sodium carbonate solution and improve control within the specified range. rust resistance The reason is to reduce rust consume, PH value decreased, bacteria, work concentration is too low to be addressed for these reasons as a result of excessive consumption of rust, but also additional rust in the working fluid Copper wire drawing oil, copper wire drawing oil, cleaning agents supplied by Indira Trask Chemicals (China) Limited. Indira Trask Chemicals (China) Co., Ltd. (www.delaska.com) strong, credible, in Shenzhen, Guangdong lubricant (grease) industry has accumulated a large number of loyal customers. The company better work attitude and constantly improving innovative ideas will lead Indira Trask chemicals into the brilliant and you work for a better future!