XK3110 Weighing control meter / weighing instruments / accumulate measuring instruments / batching meter

 XK3110-B High Speed ??Weighing controller XK3110-B High-speed Weighing Batch Controller [XK3110-B High Speed ??Weighing controller] XK3110-B Introduction Weighing speed controller is designed for a variety of ingredients systems for improve dosing accuracy and dosing process automation and control instruments. Weighing XK3110-B high-speed controller with advanced, highly integrated microprocessors and integrated circuits, leading technology, quality and reliable performance, with high control accuracy and good anti-jamming capability; the use of advanced SMT technology, small size, high integration; built-isolated RS232 and RS485 communication interface or remote multi-point communications; built-in isolation of high-precision DA converter, 4 ~ 20mA analog output can be used to achieve weight signal change loose input, all-digital way of regulation and control for easier operation. [XK3110-B High Speed ??Weighing controller] Product Brand: Bell Dongfang Electrical Products Model: XK3110-B Measuring range: 30 tons Accuracy: 3 Display: Digital Dimensions: 96mm (width) * 48mm (High ) * 156mm (deep) hole size: 92mm (width) * 44mm (H) Working environment: 0 ~ 50 ℃ [XK3110-B High Speed ??Weighing controller] Technical Specifications Power: 220V ± 15%, 50Hz or 110V ± 15%, 60Hz; Power: 6W; Range: 500 to 30,000; indexing pitch: 1,2,5,10,20,50; sensor excitation voltage: DC 9V ± 5% or 5V ± 5% (only B2A type), the maximum load capacity of 150mA; Output: open collector output, the maximum DC 24V, 0.3A; communication: serial EIA-RS232 / RS485 standards; analog output: 0 ~ 24mA adjustable, 16-bit resolution rate, maximum load resistance 500Ω. [XK3110-B High Speed ??Weighing controller] Introduction to set the indicator as a whole and ingredients controller; dual monitor also shows gross and net weight; the smallest batching controller panel measuring only 96mm * 48mm; Maximum control of four different types of materials; all preset data with power protection; automatic zero tracking; Tare function keys; all materials have their own crude measurement, fine metering and fall compensation; with software fully digital tuning function; optional RS485 standard serial input-output port; RS485 communications can achieve multi-point communication; via RS232 / RS485 data output ingredients; display accuracy up to 15000; tolerance and tolerance test output; with discharge control function ; start production conditions can be set via the menu; production conditions can be peeled by the menu settings; Auto-zero function with power-on; after the completion of the ingredients, with net display hold function; can set the maximum gap, ensure the automatic compensation function is not due to mechanical failure caused by an error; Slow batching delay time can be set via menu; the number of comparisons can be set via the menu in order not to say the impact caused by wrong body control; start peeling delay time can be set via menu; peeled detection times can be set using the menu to avoid peeling error in unstable situations; fast and slow ingredients prohibit comparison time can be set separately; with dual digital filter; when with less than tolerance, can be used to add the amount of ingredient ; can be set via the menu parameters school said; can be zero alone, school weighing spacing operation; 4 ~ 20mA high resolution analog output; the input port selectable active, passive two ways (factory designation). XK3110-B High-speed Weighing Batch Controller Specially for types of batching system, XK3110-B high-speed weighing batch controller is used to improve the accuracy and automaticity of batching process. About XK3110-B High-speed Weighing Batch Controller 1. conbine weight indicator and batch controller; 2. gross weight and net weight simultaneous displayed on two monitors; 3. the minimal weighing batch controller, the panel size is 96mm * 48mm; 4. 4 different componets maximum; 5. power-off protection function; 6. automatic zero tracking; 7. one button to peel; 8. the componets have self gross measuring, self accuracy measuring and self fall correction; 9. digital software adjusting; 10. multipoint communication can be achieved by RS485 communication port; 11. batching data output through RS232 / RS485; 12. display accuracy is 1/15000; 13.check out of tolerence and overproof output; 14. unloading control function; 15. production starting can be preset; 16. peeling in production can be preset; 17. autozero when power on; 18. net weight can keep display when batching completed; 19. the fall range can be set to ensure self fall correction keep right when mechcanical fault; 20. the delay time of slow feeding can be set; 21 . comparisons can be set; 22. double digital filter; 23. dosing add is allowed when dosing weight less than tolerance; 24. adjusting parameter can be set; 25. calibration and weighing space could be set separately; 26. 4 ~ 20mA high precision analog output; 27. active input or passive input (factory designated).