Foshan, Shantou, Shaoguan steel structure plant spray cooling engineering

Foshan, Shantou, Shaoguan steel structure plant spray cooling engineering Shenzhen City Jia Qiang East Environmental Protection Technology Co., Ltd. specializes in artificial fog products, namely artificial fog, spray cooling, fog technology development, system design, equipment manufacturing, installation, sales and after-sales service as one of the technology-oriented enterprises. Electromechanical domestic first-class R & D personnel and senior skilled workers, research and development over the years has been adhering to the essence of "respect for people. Serve the people," the domestic first-class enterprises, build domestic spray cooling professional and technical standards, it has been widely recognized by users. The main products include: spray cooling equipment, spray humidifier, spray deodorant disinfection equipment, spray dust removal equipment, artificial fog landscape of high performance spray mechatronics engineering products. It has been widely used in municipal, transportation, aviation, electric power, factories, coal mines, ports, petrochemical, livestock, food, medical, printing, garden, electronics, automotive, agriculture and other industries. Due to limited release in the online product content, welcome calls to understand the range of performance using spray cooling steel structure plant engineering, price and product. Want to know more cool spray steel structure plant engineering information, please copy the link Baidu, enter: www.szdjq.com spray technology: 1, high-pressure spray equipment, spray systems technology uses different precision fine atomizing nozzles, fine atomization The spray nozzle ancillary equipment operation can produce fog particles range 5-10μm, 10-25μm, 25-55μm different degrees of micro-fine mist. 2, water media: use clean tap water or equivalent neutral water, the water pressure 0.01 ~ 0.3Mpa, low cost of water, spray the effect is significant. 3, the working temperature: 45 ° C; Ambient temperature: 5 ° C ~ 45 ° C; relative humidity ≤90%. 4. The ability to run: 220 / 380V / 50Hz, pumping stations can provide a range of conventional pressure 1.5-110Mpa, ultra-high pressure requirements can be customized. 5, high-pressure fog machine, micro-fine mist humidifier removal equipment by air happened unsaturation quickly spread in the air, when the fog evaporate quickly absorb heat in the air, and further air humidification, to humid air, cooling room temperature, except for air to clean the air of dust particles purpose. 6, this artificial fog spray system and because the spray particles themselves can be used to eliminate electrostatic adsorption, and negative particles produced in high-speed atomizing ambient air after spray very fresh and cool. In recent years, the rapid rise of emerging technologies to improve the lives of a low-cost environment. Foshan, Shantou, Shaoguan steel structure plant spray cooling Engineering notes 1. All lines of the entire system can not use ordinary steel rust easily, high pressure seamless copper, high pressure seamless steel tube or high-pressure rubber steel composite pipe, avoid rust water nozzle clogging. 2. You can pipe directly connected to the water, but the addition of powerful filters must avoid solid particles in the water clog the nozzles. 3. If the machine is used in cold areas, it should pay attention to take freezing measures; Host installed outdoors, measures must be taken to rain; after use, cut off the water, working five seconds, drain the remaining water from the pump to prevent freezing high-pressure pump . 4. Non-dry state, running pumps. 5. Installation height of the nozzle, it is recommended at least two meters from the ground height of at least 0.5 meters from the top of the house; on the one hand to increase the evaporation of ultra-fine mist particles in the air, vaporization of time, on the other hand to avoid the ultra fine mist particles sprayed into the barriers It was to produce water droplets. 6. Mounting height horizontal angle nozzles 5∽15 ° upward tilt angles for optimal use. 7. Connecting pipelines each nozzle gap 100M 300MM, each have a fixed point 2M; avoid long-term use of the connecting line, bending, resulting in long-term retention of residual water in the pipeline to form a precipitate, clogged nozzles. 8. Boot before, please release to no pressure state regulator, slowly adjust regulator boot, observe the pressure gauge display. These are the details of spray cooling steel structure plant engineering, if you want to learn more about the price, type and size spray cooling system, steel structure in the end spray cooling plant project is appropriate there with you, when you need to install the device Note what factors and so on, please call dwell understand, small quantities of a few minutes to make a budget. Purchasing steel structure plant spray cooling works, please look for good-East Shenzhen Environmental Protection Technology Co., Ltd. Solemn promise: All spray systems manufactured by the company have been layers of testing, quality assurance. Out products from the company are to enjoy free one-year warranty and lifetime maintenance cost fee policies. Want to know more cool spray steel structure plant engineering information, please copy the link Baidu, enter: www.djq168.com