Siping temperature and humidity testing equipment brand strength

Constant temperature and humidity test equipment Uses: The unit provides constant temperature and humidity test equipment hot and humid environment to compare rubber, plastic materials testing before and after the change and the strong decline of minus degrees; the machine can simulate container environment to detect rubber plastic at high temperature and humidity, fading, shrinkage of the case, the unit specialized test a variety of materials, heat, cold, humidity performance. Temperature and humidity testing equipment Model: TH-80/150/408/800 / 1000L (MH) Studio Size: 80L, 120L, 150L, ??225L, 408L, 800L, 1000L, or upon request made, walk-in constant temperature wet room up to 100 cubic meters. Constant temperature and humidity test equipment structure and materials: observation window: three vacuum glass, easy to observe the test use, size: 320X250X40mm; window sweatband design: electric devices to prevent condensation; lighting design: high brightness window lighting energy-saving lamps, easy to observe the test; the test hole: 50mm diameter body attached to the left side of a stainless steel manhole covers, silicone plugs 1 (optional multiple or 100mm); machine pulley: easy to move (to adjust the placement) and strength bolt . (fixed position) supporting the use; inside the racks: SUS # 304 stainless steel racks 2 square punching and rail group 2 (adjust spacing); Machine Weight: about 300KG communication interfaces: RS-232C terminal one. Can be connected to a computer, print curves (computer, printer self-made). Within the box material: mirror stainless steel plate (SUS304 thickness of 1.0mm); Carton Material: gauze stainless steel plate (thickness 1.0mm); stratosphere design: effectively prevent condensation at the top of the box; Insulation: thermal insulation layer (hard Polyurethane foam, 100mm thick); door: Monolithic gate, single window left open. Plane embedded handle Hinge: SUS # 304. Dual-channel insulated airtight packing, effectively cut off from the heat exchanger inside and outside the box; constant temperature and humidity test equipment main technical parameters: 1. Temperature range: low temperature 0 ℃ --- 70 ℃, the lowest reach -150 ℃; high temperature 150 ℃ up to 200 ℃. 2. humidity range: 20-98% RH, can be customized according to the requirements of 10-98% RH 3. Temperature fluctuation: ± 0.5 ℃ Temperature uniformity: ± 2 ℃ 4. heating rate:> 3 ℃ / min 5. cooling rate:> 1 ℃ / min up to the fastest 5 ℃ / min 6. Humidity fluctuation: ± 3% RH 7. humidity uniformity: ± structure and parts 2.5% RH 8. temperature and humidity testing equipment: 9. inside and outside the box material: inner box -USU # 304 stainless steel mirror; Carton -USU # 304 stainless steel or SUS # 304 stainless steel spray rippled 10. Insulation Material: rigid polyurethane foam + glass wool 11. Controller: P meter installed, South Korea TEMI man-machine interface touch screen controller, the main configurations are used in Italy, Denmark or Japan 12. The refrigeration system components: France Taikang fully enclosed compressor / environmentally friendly refrigerant 13. Protection: compressor overheating, over-current, overpressure, heated humidification air burning in the box from the warm, water alarm system 14. Power: 3ф5W380VAC ± 10% or 2ф3W220VAC ± 10% humidity testing equipment as standard: 1. Window (box lighting), ф50mm cable hole (in the left even) one of two sets of sample holder (height adjustable), mobile working wheel, humidification water tank 2. Optional communication interface, recorder, built-in glass doors and the operation hole, with 3 connected to the computer and printing software. Another special requirements can be customized 4. Control method and characteristics: balanced thermostat humidity control system (BTHC), with PID controlled SSR, the heated humidification system is equal to the amount of heat and moisture loss, it can use long-term stability. Meet the following criteria: GB2423.1-89 low-temperature test methods, GB2423.2-89 high-temperature test methods, GB2423-93 test D6 Damp heat test method, IEC68-2-30 test methods change. Paddy ASHDOWN Lai specializes Humidity Chamber / humidity testing machine / constant temperature and humidity test equipment / constant humidity chamber / heat chamber / high and low temperature / environmental testing machine / rapid temperature change chamber, packaging testing equipment, environmental testing equipment, tensile testing machine and other products, please contact us For more information about Aisi Li detection equipment constant temperature and humidity test equipment related to the company details of the consultation can be added QQ:! 2850687972 or visit Aisi Lai Instruments Website: http: //www.hwhssyx.cn/a/cpzs/hwhscssbcj/6.html www.cjsyt.com