Q32 series shot blasting machine

Q32 series shot blasting machine: This machine is a new product and foreign technology, design and development, is a high cleaning efficiency, compact structure, low noise, complete and good cleaning equipment, it has the following characteristics : This series is suitable for a variety of medium and small castings, forgings and machined parts surface cleaning, descaling and shot peening process. It is suitable for different production scale, can be used alone, can also be more than one associated with the continuous conveyor components, composing the production of clean-up lines. Large, medium and small ideal cleaning equipment to clean the workpiece. Q32 series shot blasting machine with advanced design, reasonable structure, low energy consumption and high efficiency. 1. Q32 crawler shot blasting machine uses a cantilever centrifugal blasting device, with a simple long lifetime and so on. 2. Q32 crawler shot blasting machine BE type separator, with good separation and higher productivity, to improve blade has a positive effect. 3. Q32 crawler shot blasting machine baghouse dust emission concentrations below the national standard, which greatly improved the operator's working environment. 4. Q32 crawler shot blasting machine wear-resistant rubber track, reducing the impact and damage to the workpiece, the lower the noise of the machine. Q32 series is made of high strength wear-resistant rubber crawler track or manganese steel workpiece loading by shot blasting high-speed projectiles thrown on the track reversal of the workpiece, the purpose of cleaning up. It is mainly applied to clean castings, forgings, aluminum, stainless steel, copper and other small pieces of artifacts. Shot blasting device body and room layout have to go through the computer simulation to determine the three-dimensional dynamic projectile, thrown out of the coverage area so that the shot stream and accurate coverage of the surface, the projectile from the workpiece in all directions at the same time threw the surface of the workpiece; adoption wear-resistant steel clip rubber track, reducing the impact on the workpiece, damage phenomenon, reducing the noise of the machine. Using winnowing separator, with good separation and higher productivity, reducing the wear parts (such as shot blasting blades) wear; use bag-type dust collector, dust emission concentrations below the national standard, improve the working environment of workers; workpiece cleared, you can automatically track reverse discharge. Using the popular form of no pit, saving foundation pit construction costs. The machine is suitable for multi-species, medium and large batch workpiece surface rust or shot peening. Cleanup of the workpiece must be afraid of a collision of a single focusing 150kg casting and heat treatment following parts, production of Q32 track shot blasting machine has the following advantages: 1, using the German LUOSIl's high speed projectile cantilever centrifugal blast wheel technology, significantly improve the cleaning efficiency, satisfactory cleaning quality, with long life, simple structure, low failure rate. 2 Shot Blasting Room and the layout have to undergo a computer simulation to determine the three-dimensional dynamic projectile after, the coverage area by thrown projectiles flow and accurate coverage of the surface, the projectile from the workpiece in all directions at the same time threw the surface of the workpiece, leaving no dead space to ensure that the workpiece processing. 3, wear-resistant steel clip rubber track, reducing the impact on the workpiece, damage phenomenon, machine noise and vibration are small, optional bag-type dust collector or cyclone dust collector, dust concentrations are up to national safety standards, reduce machine friction, increase service life. 4, high level of automation, saving manpower, while using the landless hole pattern, reduce business costs of this type of shot blasting machine use are: for multi-species, medium and large mass of the workpiece surface rust or shot peening machine use High-speed rotation of the impeller, the projectile thrown on the inside of the drum continuously flip the workpiece, the purpose of cleaning up. It is suitable for all sectors of the small small castings, forgings, stampings were shot blasting, descaling and surface hardening, especially for surface cleaning and strengthening afraid of a collision of the parts. After casting shot blasting, machining surface to facilitate the next machining process, not only can save processing time, but also to protect the machine from damage; non-processed surface after the painting, not from durable, improve product quality of life and appearance. This machine is the use of an annular rubber track to form a working space, is clean up the workpiece is rotated continuously track the testimony flip projectile at high speed centrifugal force blasting device thrown on the track continuous roll of the workpiece, in order to achieve cleanup. This applies to all sectors of the small casting, forging, stamping parts and gears, springs and other sand, rust, scale and surface hardening place. Skip materials using automatic rotary automatic unloading track, greatly reducing the labor intensity. The new bag-type dust collector, so that dust emission concentration less than the national emission standards and improve working conditions. Specifications: Q326, Q3210, QR3210 technical parameters: Parameter Parameter Unit Q326 Q3210 QR3210 Productivity Productivity T / h 0.6-1.2 3-5 1.5-2.5 feeding quantity Loading weight kg 200 800 600 single maximum weight The maximum weight of one piece kg 1015030 side plate diameter Diameter of roller mm Ф650 Ф1000 Ф1000 effective volume Available capacity m3 0.15 0.4 0.3 Shot volume Pill impelling volume kg / min 100 250 250 Dust wind Dedusting air volume m3 / h 2200 6000 5000