Town lighting sandblasting sandblasting machine manufacturers supply automatic blasting machines town good quality superior products ..

Town lighting accessories sandblasting glass rod automatic transmission sandblasting machine (which can be non-calibration, design and production customers need equipment) Features 1, using triangle belt conveyor parts, will not accumulate sand, the belt speed can be achieved with the sandblasting process requirements Frequency Control; 2, each angle can be adjusted freely gun gun rack and automatic frequency swing point sandblasting, flexibility; 3, on the use of advanced cyclone system configuration, good dust separation efficiency, high blasting efficiency; 4, the use of advanced PLC electric control system, high degree of automation, good stability, low failure rate; 5, the nozzle using a special high wear-resistant carbide material, long life; 6, a separate bag type dust removal system, dust extraction ventilation Good; 7, abrasive waved spiral conveyor and pneumatic recovery combined with a stable recovery merciful. Technical parameters Model XT-8060-8A automatic transmission sandblasting machine Overall dimensions (area): 3600 * 800 * 2600 (mm) dust box size: 600 * 800 * 800 (mm) gun: 8 (6 , 10,12,16) support Power: 380V / 50HZ three-phase five-wire system Dust box motor: 5.5kw separator air flow: 10m3 / min compressed air source: 2-7bar (kg / cm2), flow 10-12m3 / min Machine noise: <85dB dust emission: <0.4mg Operating temperature range: -10 to 45 degrees Total power: 7.08kw edit this paragraph common faults and troubleshooting fault: a lot of abrasive dust into the bag. Check: Check for new cleaner bags with separate adjustment opening is too big and too fine abrasive. Solution: 1, generally eight hours after use can be eliminated transfer a small mouth; 2, using coarse abrasive. Fault: abrasive omissions in the workplace inspection: Check whether the holes or clamping cleaner bags. Solution: 1, to replace the vacuum bag; 2, re-clamping cleaner bags. Problem: When blasting clear vision inspection: 1. Check cleaner bags clogging; 2. Have blocked aging cleaner bags; 3, containing abrasive dust is too much; 4, whether the recovery tube is blocked; 5, the gas nozzle hole is too big and the air pressure is too high. Solution: 1, to replace the vacuum bag; 2, beat vacuum bag; 3, replace the abrasive separator regulator adjustment with the opening; 4. Check recovery tube blockage causes; 5, the aperture is not big 5.6MM lowered the recommended pressure. Problem: Low efficiency of check processing: 1, check the pneumatic pressure is too low; 2, the nozzle and the gas nozzle is too small; 3, in the presence or absence of excess abrasive dust. Solution: 1, to increase the pressure; 2 replace larger nozzle and gas nozzle; 3 shift into new abrasive. Problem: uneven abrasive ejected inspection: 1, check whether the abrasive less than normal; 2, the air pressure is low; 3, the nozzle is blocked; 4, abrasive damp; 5, the separator regulator gap is too small . Solution: 1, to add more abrasive; 2, an increase in pressure; 3, clear the blockage; 4, add dry abrasive; 5, check the pneumatic air gap adjustment. Edit Scope This section applies to the plate, dish, Quartet, profiles and sandblasting other odd-shaped workpieces, such as: flat stainless steel sheet and can steel, glass, steel, stone, non-stick pan, toast oven, computer chassis, functional DVD panel, notebook, computer motherboards, iron plate, decorative pieces, signs badges, communications equipment, aluminum plates, profiles and other shaped pieces. Uses: used to clean up mold, leather, glass, carved stone, wood carving, spray processing, the rough surface of the workpiece, descaling, degreasing, descaling, deburring, can be used for spraying, electroplating pre-treatment process, to improve the coated (plated) adhesion layer surface and all of surface treatment. Pretreatment before painting the surface coating, paint front; front spray; before metal spraying; before galvanizing, chromium, nickel; pre-oxidation treatment; ...... 1 before testing. Changes in the physical and mechanical properties of the workpiece to increase or decrease the surface roughness; surface tensile stress becomes compressive stress; improve surface lubrication; reduce noise coupling member movement; improve surface friction coefficient ...... 2. Polishing finishing metal outer decorative surface machining a workpiece surface; get matte or diffuse surface; polished wood surface of the article ...... 3. Parchment and other art cleaning and preservation 4. Surface cleaning brushes, contactors and wiring technique, etc., to improve the conductivity of the advantages of sandblasting machine: 1. sandblasting machine metal parts from damage basic dimensional accuracy will not change; 2. the part surface from contamination, abrasive and parts of the material is not a chemical reaction; 3. blasting machine can easily handle recess, recess and other hard to reach area, a variety of particle size of the abrasive can choose to use; 4. significantly reduce processing costs, mainly blasting machine work efficiency, can meet a variety of surface finishing requirements; 5. Low energy consumption, costs province; 6. blasting machine does not pollute the environment, eliminating the need for environmental management costs; environmental index's machine "People's Republic of China environmental protection standards" and "water discharge standard GB 8978-1996", "air emission standard GB 16297-1996", "noise and vibration standard GB 12348-90" and other relevant provisions of the environmental index of the machine fully meet the requirements. Machine matching requirements 1. This machine Power requirements: three-phase, 380V, 10KW, 50HZ power outlet; 2. The machine Air source: dry, the pressure within the range of 5 ~ 8bar choice, traffic must reach 400 cubic meters or more; 3 Abrasive requirements: In order to achieve the best results can be 30 to 280 mesh glass beads or emery purpose. The gas supply piping requirements: pressure hose, 1.0 inch. 5. Power line requirements: three-phase four-wire, more than 10 square meters. 6. Workshop requirements: strong ultra-flat surface, 15 to 20 square meters of space, high above 3M. Quality sound system, improve our company's quality assurance system, combined with the company's products and all kinds of engineering, manufacturing of the actual situation, the quality of management to implement a comprehensive and effective approach, especially the development of the company's quality assurance program. u meet the specified needs and uses; u product quality to meet user requirements and expectations; u in line with national and technical specifications related businesses; u reasonable prices, access to good economic competition. u productive sectors are strict, all the factory equipment required to test the multi-channel several people.