EPDM EPDM rubber shrink tube heat shrinkable tube factory direct wholesale

EPDM EPDM rubber shrink tube heat shrinkable tube factory wholesale direct Our main products are: 175 ℃ high temperature heat shrink tubing semi-rigid, transparent flame retardant heat shrinkable tube with plastic double-wall heat shrink tubing, 150 ℃ oil thermal control, 200 ℃ Viton heat shrink tubing, heat shrink tubing, heat shrink tubing logo, 200 ℃ heat-shrinkable marker sleeves, 260 ℃ Teflon heat shrink tubing, the wall thermal control, environmental protection heat shrinkable tube, 150 ℃ military standard environmental retardant heat shrinkable tube, magnetic heat shrinkable sleeve, heat shrink tubing neoprene, EPDM EPDM heat shrink tubing, heat-shrinkable tubing brake hose protection, thermal shrinkage tube, high-pressure busbar thermal control, yellow-green shrinkable tube, hot melt tube, Teflon tube, according to customer requirements non-standard Size and color EPDM rubber EPDM shrink tube heat shrinkable sleeve Application of the EPDM rubber (EPDM) processed by a special process, compared with ordinary EPDM rubber hose, physical and mechanical properties of the product better, higher voltage resistance, good wear resistance. Mainly used in wire harness insulation or electronic components, solder rust and corrosion, mechanical protection and waterproof seal, widely used in electronics, automobile, decoration and lighting engineering and consumer goods. Characteristics shrink ratio 2: 1 soft, flexible, good grip high temperature levels, up to 150 ℃, also available at 180-200 ℃ under short-term or intermittent use 150 ℃ excellent electrical insulation, weather resistance, UV aging high performance acid and chemical solvents performance meets RoHS, REACH environmental standards operating temperature range continuous use temperature: -55 ℃ ~ 150 ℃ lowest initial shrinkage temperature: 70 ℃ Minimum fully recovery temperature: 120 ℃ performance test performance requirements The method typical longitudinal shrinkage ≤10% ASTM D 2671 ≤5% tensile strength 10.4MPa min. ASTM D 638 ≥14MPa elongation at break 200% min. ASTM D 638 ≥400% after aging tensile strength (heat aging 180 ℃, 168 小时) 7.3MPa min. ASTM D 638 ≥9.8 MPa elongation at break after aging (heat aging 180 ℃, 168 小时) 100% min. ASTM D 638 ≥200% low temperature flexibility (-50 ℃, 4 小时) ASTM D 2671 No cracks through the breakdown voltage and breakdown 2000V, 60sec, no breakdown by ASTM D 2671 breakdown strength 10 KV / mm min. ≥12 KV / mm Volume resistivity 1013Ω · cm min. ASTM D 876 ≥ former 1013Ω · cm Size Sizes Specifications contraction (mm) after complete shrinkage (mm) Scope (mm) Standard Packaging (m / volume) ID (min.) inner diameter (max.) thickness Ф6 6.0 3.0 0.80 ± 0.10 3.5- 6.0 50 Ф8 8.0 4.0 0.90 ± 0.10 4.5-8.0 50 Ф10 10.0 5.0 1.20 ± 0.10 5.5-9.5 50 Ф12 12.0 6.0 1.20 ± 0.10 6.5-11.5 20 Ф16 16.0 8.0 1.50 ± 0.15 8-15 20 Ф20 20.0 10.0 1.50 ± 0.15 11- 19 20 Ф30 30.0 15.0 1.80 ± 0.15 17-29 20 Ф40 40.0 20.0 2.00 ± 0.20 22-38 20 Ф45 45.0 22.0 2.00 ± 0.20 25-43 20 Ф50 50.0 25.0 2.00 ± 0.20 27-48 20 Ф60 60.0 30.0 2.10 ± 0.30 32- 58 10 Ф70 70.0 35.0 2.10 ± 0.30 37-68 10 Other specifications size can be customized color standard colors: black other colors can be customized.