Vertical 30 tons of plastic storage tank 30 tons of acid tank

Plastic reservoir with a purely linear low density modified polyethylene (LLDPE) as raw material, using a special rotational molding process as a whole. With no welding, impervious, non-toxic, light weight, anti-aging, impact resistance, corrosion resistance, long life and other advantages. It can be stored at temperatures below 60 ℃ media. Capable of storing vast majority of inorganic acids, alkalis, salt solutions and some organic solvents, corrosion resistance several times stronger than fiberglass, can partly replace stainless steel titanium, nickel alloy steel and other advanced materials, product storage and transportation of dangerous goods in line with regulations, it is safe and efficient corrosion-resistant equipment. This product complies with national health standards, alternative food-grade stainless steel container shipping solution. Plastic polyethylene tank also has easy installation, the annular rib to improve rigidity intensity. The product does not require the addition of stabilizers, enhancers, etc., but when exposed to outdoor air, carbon black was added (2%) to improve the resistance to ultraviolet light. Applicable to a variety of external harsh installation environment. Plastic tanks using rotational molding process. 1, material plastic tank company produced special material for rotational molding - linear low density polyethylene (LLDPE) or a linear medium density polyethylene (LMDPE). It can be dressed normal inorganic acids, bases, salts and many organic substances most under. 2. The minimum plastic softening point of 108 ℃, the maximum fragmentation point of -70 ℃, it is generally used in the liquid holding temperature of -40 ℃ to 60 ℃. If the content liquid temperature is higher than 60 ℃, should be configured metal reinforcing sleeve, to prevent deformation of the tank to soften. If the storage tank for the chemical reaction or diluted, should be done prior corresponding experiment, measuring the reaction or diluted maximum temperature. 3. Accessories configured according to the application provided by the customer, there are PP, PVC, ABS fittings, PP, PVC, PE flange options. When substances containing acid, to configure the PVC, PP or PE accessories and acid washers. In costumes organic compounds (especially organic solvent), the configuration is not easy to dissolve a rubber gasket. 4. This product is not suitable for containing strong oxidizing agents (such as temperature at 60 ℃, over concentration of 50% concentrated sulfuric acid, 30% nitric acid, etc.) and good organic solvent (acetone, cyclohexanone, formaldehyde), etc. 5. can not determine whether a substance containing, please refer to "polyethylene chemical properties table." 6. Install the tank foundation required level and be able to pressure, such as steel structure, the gap can not be too large and should be on top covered with wood or iron. 7. The chemicals in storage tanks, around the field should have good drainage trench and dilution devices. 8. Since the bottom of the tank inevitable projection into the tank at the time of molding form spherical cap, so the foundation should be made similar to the shape of the bottom spherical cap (proposal on the basis of the level of the tank bottom with sand paved the corresponding ball coronal ). 9. The large size tank at the time of installation should pay attention to safety, as far as possible with the crane, when I do not know the method, please contact us. 10. Plastic fittings factory is tightened during transportation, loading and unloading may be loose fitting, so before using it if the sealing performance of the connector to be checked, you can add the liquid was observed over joints for leaks. Chemical storage tanks containing liquid, preferably water leak, to avoid causing a lot of damage. 11. The lower part of the tank pipe fittings or flanged be perpendicular to the barrel wall, preferably using soft links, so as not filled with liquid, the upper and lower sides of casks lead to differential expansion header damage cause leaks, severe damage to the head and barrel. 12. The liquid inlet from the bottom of the tank when the higher, the inlet should be bent to allow the tank wall tank wall falling down into the liquid, reducing the impact on the bottom. 13. A large-capacity storage tank (20 cubic meters or more), a metal reinforcing sleeve can be used to limit the swelling deformation of the joints of the barrel, so as to avoid cracking of the hole portion. 14. Installation mixers and other heavy equipment subsidiary, when he shall work on the tank top and initiations can not bear a person's weight or, please make another rack or a ladder, and pay attention to work safety. 15. In the case where the level of control, should be fitted with an overflow port to prevent the liquid from manhole overflow, causing unnecessary harm. 16. The inlet, larger drain flow, corresponding flow of the exhaust pipe should be installed in. 17. When converting containing liquid, please get in touch with me again.