Liao Ning Yuetai 596 glue

Liao Ning Yuetai 596 glue, Loctite 596 glue wholesale, 271 US Loctite glue Loctite 263 N-7000 Loctite glue Loctite 680 Loctite glue factory direct sales worldwide, Shenzhen Trading Co., Henkel Loctite Loctite distributor in the United States Henkel is a company with 130 years of history of multinational corporations, global consumers 125 countries trust in brands and technologies from Henkel. Henkel, a Fortune 500 company. As early as in the Qing Dynasty, Chinese trade with China has another job. Today, the Chinese market has become the most important part of Henkel's global market, its products are: thread Loctite glue, Loctite pipe thread sealant, Loctite structural adhesive, Loctite UV glue, Loctite cyanoacrylate, music Thai anaerobic adhesive, Loctite silicone rubber, Loctite cylindrical solid adhesive, Loctite accelerator, Loctite cleaning agents, anti-bite agent Loctite, Loctite lubricants, Loctite metal repair, etc. Henkel Loctite adhesives. Loctite 596 Product Description: Loctite 596 glue is a single-component, room temperature curing adhesive / sealant and high-temperature rubber gasket. Superflex TM 596 is a red, viscous non-slumping, low volatility cream body. When cured to a flexible rubber when the product will emit a small amount of acetic acid (vinegar taste similar). The product after contact with atmospheric moisture will be cured to form a tough, flexible, fire and oil resistant silicone rubber sealant. Superflex TM 596 anti-aging, large steam and thermal cycling without hardening, shrinking or cracking. This product is particularly suitable for the automotive industry 600 ° F (650 ° C intermittent) temperature sealing flange, because it can meet the requirements of low silicon volatility. This ease of use is not slumping performance sealant so it can be used for the horizontal plane and the vertical plane can typically use the product both for equipment maintenance, and can be also used small, medium and large-sized OEM . ? High temperature (600 ° F) adhesives - can be bonded to most substrates including silicone rubber. ? Gasket sealant. Can be used to improve ordinary metal gaskets and usually at 600 ° F condition fails pre-cut gasket seal. ? In situ since a gasket adhesive / sealant. It can be used instead of the usual conditions at 600 ° F failure preformed gasket? Heatable element sealing and encapsulating electronic devices. ? Sealants and adhesives, can be used for assembly and repair of industrial furnaces, ovens, boilers, exhaust pipes and ducts. ? Adhesive sealants, MIL-A-46106A, Category 1. UNCURED MATERIAL Typical Value Typical silicone polymer matrix (acetate-based curing system) color red appearance smooth spreadable paste (thixotropic) no caking, the same oil, the same real proportion @ 77 ° F (25 ° C) 1.05 ± 0.04 non-volatile solids content of 98% (excluding the solvent) Tack Free Time (@ 75 ° F, 50% RH) 30min full curing time of 24 hours (1/4 "beads) Flow / slide No collapse rate (0.2 inches Boeing Flow test) the extrusion rate (1/8 "glue nozzles, air pressure 90psi) 180g / min flashpoint TCC> 200 0 F shelf life of 1 year @ 80 0 F curing low toxicity description temperature at 77 ° F, 50% relative humidity conditions, this product will debonding within 15-30 minutes. After at least 24 hours to reach full strength will be completely cured. Curing speed depends on temperature, relative humidity, material thickness and the prevailing humidity. After the material is completely cured, acetic acid (similar to vinegar) taste will disappear. The curing process, the sealing of acetic acid gas will cause some minor corrosion of metal surfaces, such as copper, steel and other metals. Use with adequate ventilation conditions. Typical performance after curing material (thickness - 0.125 "layer at a temperature of 78 ° F, 50% relative humidity cured for 7 days at room temperature (77 ° F) under test conditions) Typical Rockwell hardness, ASTMD676, Shaw s A 36 Tensile strength, ASTMD412, psi (MPa) 390psi elongation, ASTMD412 (%) 370% 50% modulus @ 85 @ 62 @ 75% 100% 107 Adhesion (wire mesh and aluminum) Cut Viscosity * (PSI) 150 stripped viscosity * (PSI) 25 (* contact surface bond failure) the role of the heat temperature range -95 0 F ~ + 600 0 F (intermittent up to +650 0 C) silicone / silica volatile content, wt% (10 ± 0.01g sample at 70 ± 2 分钟 @ 121 0 C air circulating oven) and FDA should use especially for high-temperature (600 0 F) experienced by packaging and sealing device, e.g., an exhaust Cross manifold oven, high-temperature oven and blast furnace, etc. For frequent exposure to higher temperature sealing and bonding devices 450 0 F-600 0 F under, this product is the best choice as a cushion situ sheet rubber / sealant, Superflex TM red high temperature RTV silicone sealant in the package include the use of an automobile valve cover, oil pan, water pumps, end seals and rear axle housing package, but also shows prominent features. For Prefabricated silicone rubber gasket bonding and repair, is an excellent adhesive. package Precautions Do not use red Superflex TM high temperature RTV silicone rubber sealant for continuous contact with hydrocarbon fuel carburetor or fuel control device. In that case, the product will lose the excessive expansion that mechanical properties. Usage Guidelines Before using this product, should be all the mating surfaces with Loctite ODC-free cleaning agent and degreaser dry cleaning agent. Recommended Use Loctite Chisel TM Gasket Remover # 79040 remove all old packaging materials left behind on the mating surfaces. Finally, then Loctite safe solvents # 755 or mineral spirits to clean and dry surface. This product will be a continuous bead like dripping all around the hole and the mounting surface. After the adhesive coated finish after 10 minutes with both surface and then pressing or clamping the mating face (not to cause the slide). For the exposed surfaces, sealants in 1 hour Tack will become for plastic 1/4 inch diameter droplet surface, exposed to atmospheric moisture cured about 24 hours to cure completely. Clear for Uncured Superflex TM 596 can use Loctite cleaners # 755 or mine Oil direct clean. For the cured silicone rubber may be using an appropriate scraper to scrape off, and then use Loctite Chisel Gasket Remover # 79040 or special corrosive industrial (paint) strippers dissolve the remaining rubber. Such appropriate chemicals such as chemical stripping agents must obtain from the manufacturer there. Note This product is not in pure oxygen and / or oxygen rich systems and should not be used as a sealant for chlorine or other strong oxidizing materials used. For safe handling information on this product, please consult the Material Safety Data Sheet (MSDS). Before the adhesive to be used when an aqueous cleaning solution to wash the surface of the adhesive, it is important to check the cleaning solution with the adhesive compatibility. In some cases these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic may cause stress cracking). Users are recommended to confirm compatibility of the product with such compatible adhesive material. .