Soybean hulls removed soybean peeling machine peeling machine vibration machine

Soybean peeling machine peeling machine vibration Stainless steel rectangular shaker - I pay attention to quality, honest and trustworthy, courteous service. Pay attention to the quality of every product, every detail of the design; treat every customer, every business honest and trustworthy; sincere service every customer patience to solve every problem. 24-hour customer service hotline: 13569833759 QQ: 1846387535 Contact: room manager HYSF use linear vibrating screen vibrating motor as vibration source, so that the material to be tossed in the sieve, while forward in a straight line, the material from the feeder evenly into the screening machine feed opening, generating several kinds of specifications through the multi-screen oversize, undersize fraction were discharged from their exports. With low energy consumption, high output, simple structure, easy maintenance, fully enclosed structure, no dust, auto-nesting, more suitable for pipeline operations. Use of powdered, granular materials selection and classification, widely used in plastics, abrasives, chemicals, pharmaceuticals, building materials, food, carbon, fertilizer and other industries. Technical parameters Model ZXS-520 ZXS-525 ZXS-1020 ZXS-1025 nominal dimensions mm 500 × 2000 500 × 2500 1000 × 2000 1000 × 2500 material size mm 0.074-10 0.074-10 0.074-10 0.074-10 screen surface inclination 1 ° -7 ° 1 ° -7 ° 1 ° -7 ° 1 ° -7 ° amplitude 3-4.5 3-4.5 3-4.5 3-4.5 layers 1-61-61-61-6 power Kw 2 × ( 0.4-0.75) 2 × (0.4-0.75) 2 × (0.4-0.75) 2 × (0.4-1.1) Dimensions Model ABCDEFGHIK ZXS-520 2130 966 935 566 1700 600 235 200 150 400 ZXS-525 2630 966 935 566 2200 600 235 200 150 400 ZXS-1020 2130 1368 935 1068 1700 600 235 200 150 900 ZXS-1025 2630 1368 935 1068 2200 600 235 200 150 900 linear shaker action line with the principles of the basic principles of the lower end of the motor shaft by the installed weight (Heng uneven weight), the rotary motion of the motor into a horizontal, vertical, inclined three million campaign, then the campaign to convey to the screen surface. If you change the weight of the upper and lower portions of the phase angle can change the direction of travel of the raw material. Motor Description: This series motor under the following conditions, continuous rated output excitation force. 1, the vibration acceleration: no more than 7g (g: acceleration of gravity) 2, ambient temperature: not exceeding 40 ℃ 3, Altitude: not exceed 1000m 4, power frequency: 50Hz 5, voltage: 380V 6, temperature: less than 80K (resistance France) Installation Preparation 1, with a 500-volt megohmmeter to measure the insulation resistance of the stator winding its value should be dried, the drying temperature must not exceed 120 ℃. 2. Check the motor fasteners, beware loose. 3. Check motor surface for damage and deformation. 4. Check whether the rotating flexible, if unusual, should be excluded. 5. Check the power supply, whether the lack of phase, and no-load operation for 5 minutes. Installation and adjustment 1, the motor should be fastened to the mounting surface, the mounting surface must be smooth and flat. 2, the motor can be installed horizontally. 3, motor leads with four rubber cable YZ-500V, when connected to the power lead cable does not allow emergency off, and with the vibrator firmly secured. 4, the motor should be reliable grounding, grounding means the motor, there are signs of lead terminals, can take advantage of foot solid grounding bolt. 5, the exciting force adjustment. Use and maintenance 1, the machine should be installed in electrical protection device. 2, the initial operation of the machine, once a day to check at least bolt to prevent loosening. 3, when the motor rotation direction does not meet the requirements, you can adjust the power phase sequence. 4, the motor should ensure good lubrication, run about every two weeks Supplementary lithium grease (ZL-3) once, refueling, oil cup by adding an appropriate amount of lithium grease. When using sealed bearings, motor oil cup is not installed. 5, after the machine cumulative run 1500 hours, you should check the bearing, if any serious damage should be replaced immediately. 6, when the machine is used again after parked for a long time, the insulation resistance should be measured for 500 volts megger, should be greater than 0.5 megohms. Daily maintenance 1, before the start of: (1) Check the coarse mesh and fine mesh for damage (2) Each set of beam if the locking ring 2, start: (1) pay attention to whether the abnormal noise (2) current is stabilized ( 3) whether the abnormal vibration 3. After use: namely to clean after each use regular periodic maintenance checks coarse mesh, fine mesh and springs or without fatigue and damage, if all parts of the body and cause damage due to vibration required. lubrication of parts must be lubricated. Hongyuan vibration sieve Note: the table size according to the size of a layer of screen patterns ● The company can according to user needs and design and manufacture of special types and specifications of the screening machine. ● We all technical information on the size of reserves the right to modify, such as physical and the text does not match the pattern should prevail in kind, interpretation of the Company.