Heavy calcium screening machine 800 mesh sieve heavy calcium - Hebei heavy calcium screening machine

Hotline: 13569833759 0373-2610868 Fanjing Li QQ: 1846387535 2072467445 Ali Want: yxr0518 supply - heavy calcium screening machine] [800 mesh sieve heavy calcium - Hebei heavy calcium screening machine Model: HYSF1020-2F sieve size: 1000 * 2000 Sieve: 2-200mm Power: 2 * 0.25KW vibration times: 960r / min Scope of linear shaker can powder, granular materials and small block materials screening and classification, widely used in plastics, abrasive , chemicals, pharmaceuticals, building materials, food, carbon, fertilizer and other industries. Works linear vibrating screen use vibration motor as vibration excitation source, so that the material to be tossed in the sieve, while forward in a straight line, the material from the feeder into the screening machine feed inlet uniformly produced by multi-screen On several specifications of oversize, undersize fraction were discharged from their exports. With low energy consumption, high output, simple structure, easy maintenance, fully enclosed structure, no dust, auto-nesting, more suitable for pipeline operations. Introduction linear vibrating screen is a dual vibration motor, using the principle of vibrating motor. The product high screening precision, large capacity, simple structure, good sealing, easy maintenance and can be used in the production line automation. Suitable size 0.74-10mm, less than 7% moisture, dry material of any screening non-tacky material. Raw material widely used in abrasives, chemicals, plastics, pharmaceuticals, resin powder, ceramic materials, metallurgy, building materials, food, food, fertilizer and other industries in the dry powder, granular or fine powder screening material. Prepare before installation 1. Check the motor plate is consistent with the requirements. 2. Check motor surface for damage and deformation. 3. Check the motor fasteners, beware loose. 4. Check the power supply, whether the lack of phase, and no-load operation for 5 minutes. 5. Check whether the rotating flexible, if unusual, should be excluded. 6, with a 500-volt megohmmeter to measure the insulation resistance of the stator winding its value should be dried, the drying temperature must not exceed 120 ℃. Installation and adjustment 1, the motor should be fastened to the mounting surface, the mounting surface must be smooth and flat. 2, the motor can be installed horizontally. 3, the exciting force adjustment. 4, the motor should be reliable grounding, grounding means the motor, there are signs of lead terminals, can take advantage of foot solid grounding bolt. 5, motor leads with four rubber cable YZ-500V, when connected to the power lead cable does not allow emergency break, and with vibrator use and maintenance of a reliable fixed, the machine should be installed in electrical protection device. 2, the initial operation of the machine, once a day to check at least bolt to prevent loosening. 3, when the motor rotation direction does not meet the requirements, you can adjust the power phase sequence. 4, this machine again after a long time parked, the insulation resistance should be measured for 500 volts megger, should be greater than 0.5 megohms. 5, after the machine cumulative run 1500 hours, you should check the bearing, if any serious damage should be replaced immediately. 6, the motor should ensure good lubrication, run about every two weeks Supplementary lithium grease (ZL-3) once, refueling, oil cup by adding an appropriate amount of lithium grease. When using sealed bearings, motor oil cup is not installed. Daily maintenance 1. Before starting: ⑴, check the coarse mesh and fine mesh for damage ⑵, check whether transport support demolition 2, start: ⑴, pay attention to any abnormal noise ⑵, current is stable ⑶, with or without abnormal vibration 3 After use: namely to clean after each use regular periodic maintenance checks coarse mesh, fine mesh and springs or without fatigue and damage, if all parts of the body and cause damage due to vibration, add lubricating parts must be lubricated. Installation and commissioning (a) Installation: Before ⒈ machine installation, first check the packing list and damaged parts are complete. ⒉ the setup diagram equipment installation, foundation should have sufficient stiffness and strength, all the dynamic load and static load to support the shaker. ⒊ ensure a minimum 75mm gap should be maintained between the screen box and hopper, tank and other leavened non-moving parts. ⒋ installation when all four corners of the screen box level. (B) Adjustment and commissioning: ⒈ spring must be in a vertical position, the spring seat and spring contact surfaces must be horizontal state, secured by bolts to mount the screen box spring trunnion adjusted, and then welded into one . ⒉ CONVERTED time load test of not less than two hours after the load test run qualified, can be put into trial operation load, load test can process test requirements. Size Ordering 1. screening material (thickness or size) production material requirements 2. 3. 4. Prices are per hour I plant also produces vibration motor depends on the model parameters, food processing equipment (grain sieving equipment, Pa Valley machines, blenders, etc.), vibration screening equipment (linear vibrating screen, rotary vibration sieve, sieve high frequency, mining sieve, etc.), conveyor (belt, screw machine, high temperature vibration level conveyor), hoist (NE plate chain, TH ring chain, TD bucket, etc.), feeder (GZG electromagnetic vibrating feeder, DZ motor vibrating feeder, belt feeder), and other accessories (, screen, screen frame , silicone rubber balls, springs, etc.) are welcome to contact the 24-hour customer service hotline:! 13569833759 QQ: 1846387535 E-mail: hongyuanzdsb@163.com Contact: Fanjing Li