ADSS cable connector box lever cap formula one into a connector box 24 core Power Equipment

The head cartridge Introduction: cable connector box is popular called, school called cable continued boxes, cable connection, also known as package, cable connector package and barrel, mainly applicable to various structures of overhead cable, pipeline, direct burial laying The pass-through mode and branch connections. Box of imported reinforced plastics, high strength, corrosion resistance, terminal structure suitable for the connection of the cable terminal room, the maturity structure, reliable sealing, easy construction. Widely used in telecommunications, networking systems, CATV cable, fiber optic cable network systems. The right side is binary two splice case; for protecting the connection between two or more cable, fiber optic distribution, is one of the common user access point device, mainly to complete the distribution cable and fiber optic cable in the outdoor home line The ligation, according FTTX access cassette or simply need to install optical splitter;? Edit Product Features This section box body made of high quality plastic products. ? Products using secondary pressure cable technology to ensure that no additional attenuation fiber box. ? Products with multiple reuse and expansion capabilities. ? Edit this paragraph Technical characteristics Dimensions: Height 430mm inner diameter Φ135mm Φ210mm maximum outer diameter of the cable hole neck:? Φ20mm single disc Core:? 12/24 maximum splice tray:? Minimum capacity 4-cell maximum capacity of 144 largest core melt.? fiber plate number:? 6 stretch tightness: 2000N axial tension, does not leak. ? Breakdown voltage: 15KV (DC). ? Stretch Seal: After inflatable products, can withstand 2000N axial tension and does not leak. ? Shock Seal: After inflatable products, can withstand the impact energy 16N * m (Newton * m) the impact of the three, the product without cracks, no leakage. ? Other requirements are in line with the performance of YD / T814.1-2004 standards. Edit this paragraph cable connector box ready to install the fiber optic cable 1. Remove the skin, (if there is, remove the shield and armor) each wrapped layer is then removed to expose the loose tube, the specific method, please press the cable manufacturer's recommended standard The method steps, preliminary length 3m. 2, use detergents and strengthen the core loose tube sheath, remove excess filling casing, the cable sheath 150mm long polished with sandpaper to offer. 1 cable installation, cable diameter selected according to the minimum inner diameter of the seal ring, and two sealing ring on the cable. 2, the optical cable into the corresponding hole. 3, connecting the shielding and grounding. 4, between the two sealing rings on the self-adhesive sealing tape wrapped around the sealing tape around the outer diameter of the seal ring flush to form a cable sealing end. 5, the cable seals the cable end into the hole. 6, with hose clamps through the cable holder and the cable core stiffener bracket, the cable connector box secured to the base, tighten the screw hose clamps, hose clamps until tightening up. 7, on the cable tie nylon cable ties, cut excess length. 8, the remaining unused cable holes, please sealing plug. The same block head wound sealing tape, the same requirements and 5.2.4. 9, the reinforcing member wrapped around the splice tray holder countersunk screws, and pressed. The optical fiber connector 1, late on a preliminary 1.5 turns coiled fiber, then the fiber all over the body coiled in the box. 2, please use the disc on a single fiber single buffer tube, the ribbon fiber plate Please ribbon buffering tube. At the entrance of the splice tray fastened with nylon ties. 3. The method according to the provisions of the docking of two (with) fiber splice connector card into the card slot unit, more than long please coiled in the tray. 4, splice tray cover, press on until it clicks into place. 5, according to the capacity needed for different connector box, determines the number plate weld overlay plate, the splice trays superimposed type optical fiber connector must meet snap welding unit and the inspection and maintenance requirements. Every two superposed splice trays can be six holes on the rubber fold, respectively, each of the three projections stuck on the upper and lower plate twist; four rubber folding, symmetrical positions of the two sides of the disc, such as the superposition of five Splice double-layer disc in accordance with the method described above with three buckle, three and four disc tray fastened, four and five disc tray fastened, and so five disk to stably superimposed together . When it is desired to maintain a certain level view or disc fusion cases, as long as one side of the upper plate of the two-piece folding buckle removed, splice tray can be as open as open book page. Cassette seal 1, box package: package first before the cartridge valve tip and the ground screw and tighten. ? The sealing strip embedded in the cartridge seal around the tank;? At both ends of the connector box "U" channel into the trench were also used at the seal. Note: Use the seal, do not artificially stimulate seal, to prevent leakage. 2, the connector box gently close the cover, screw fastening bolts fastening cover the order indicated in numerical order and tightened with a torque wrench ban solid, torque reaches 25N? M. 3. After 5 minutes, then a torque wrench, tighten the torque still reach 25N? M. Removal of the cover 1, according to the order of release fastening bolts 10, when the lid and the seat were still together. 2, take four fastening bolts are inserted into the cartridge body corners, symmetrical, evenly screwed into the four corners of the lid, the lid and the seat separated up