Manufacturers supply a full range of SMD aluminum electrolytic capacitors

Common specifications and dimensions 100UF-16V-6.3 * 5.4 47UF-50V-6.3 * 7.7 10UF-16V-4 * 5.4 100UF-10V-5 * 5.4 220UF-16V-6.3 * 7.7 10UF-50V-5 * 5.4 47UF-16V -5 * 5.4 470UF-6.3V-6.3 * 7.7 100UF-25V-6.3 * 7.7 220UF-10V-6.3 * 5.4 470UF-16V-8 * 10.2 4.7UF-50V-4 * 5.4 100UF-35V-6.3 * 7.7 220UF- 50V-10 * 10.2 220UF-25V-8 * 10.2 220UF-6.3V-6.3 * 5.4 47UF-25V-6.3 * 5.4 1UF-50V-4 * 5.4 100UF-50V-8 * 10.2 470UF-25V-10 * 10.2 22UF- 16V-4 * 5.4 2.2UF-50V-4 * 5.4 on SMD aluminum electrolytic capacitors patch electrolytic capacitors are one electrolytic capacitors, aluminum electrolytic capacitors currently divided into two kinds, one is a plug-in electrolytic capacitors, a species are SMD aluminum electrolytic capacitors. The main difference is that the installation and size. Conventional plug bulky electrolytic capacitors, required labor to install, thus resulting in a large volume of product, production efficiency is low. The SMD electrolytic capacitors, small size, you can use the patch installed. High efficiency, low labor cost, more compact product. Its products are mainly used for power filtering, signal filtering, signal coupling, compensation, charge and discharge, storage, resonance, filter, DC-blocking other circuits chip aluminum electrolytic capacitors [SMD Aluminum Electrolytic Capacitor] name: SMD electrolytic capacitors, referred to as: chip electrolytic. Main specifications dimensions in metric standards are divided into: Φ4 × 5.4mm, Φ5 × 5.4m, Φ6.3 × 5.4mm, Φ6.3 × 7.7mm, Φ8 × 6.5mm, Φ8 × 10.2mm, Φ10 × 10.2mm, etc. . Rated voltage: 4V ~ 100V; capacity range conventionally used: 0.1uF ~ 6800uF With the development of related technologies and materials, the maximum rated voltage up to 100V and maximum capacity to 1500uF products have been widely adopted. Aluminum electrolytic capacitor constituted: by the positive foil, foil and electrolytic negative roll into the core, with positive and negative wire leads, after impregnating the electrolyte through the guide pin lead, aluminum and plastic and then sealed. Chip electrolytic capacitors volume although smaller, but because through the electrochemical etching, the surface area of ??the electrode foil was enlarged, and its dielectric oxide film is very thin, so the chip aluminum electrolytic capacitor can have a relatively large capacity . The correct selection of a chip electrolytic capacitor products, pay attention to the parameters include: capacitance, rated voltage, temperature, life and properties (such as high-frequency low-impedance) requirements, specifically refer to this manual Currently, we offer the following series chip aluminum electrolytic capacitor products: RVS series (85 ℃ -2000 hour standard VT standard products) RVT series (105 ℃ -2000 hour standard) RVW series (105 ℃ -3000 hour standard) RVE series (105 ℃ -1000 hours frequency low Impedance) VT series (105 ℃ -2000 hour standard) RVH series (125 ℃ -1000 hours wide temperature products) RVN series (105 ℃ -2000 hours bipolar products)