Shanghai Hauck gondola cable factory outlets nationwide

When maintenance instructions basket ??? We must also make adjustments traction electric basket mechanisms to ensure conditions improve, there is no mixing. That is necessary for electric basket of site work environment have strict requirements. ??? Electric basket overload means the amount, if the overload source load capacity of 1.1 or 1.25. If it is the former, when the load in the basket raised, then quickly drop, this is a safe self-locking. Basket static load test, he can be layered, generally in accordance with the percentage of the system detects a load electric basket, but also the corresponding test waiting for the elevator, electric basket of safety locks and safety, because, if there are unusual circumstances , we must immediately closed maintenance. ????? ?? Basket wound type single rope wound type can be divided into single drum and double drum roll according to the number two: ① single drum hoist, generally for single hook lifting. One end of the rope attached to the spool, the other end of the bypass sheave and hoisting container is connected; when the drum rotates, the rope is wound on the reel or to release, led hoisting container lift. ② double drum hoist, lift for double hook. Two each fixed on a rope reel, respectively, from the reel, drawn below, when the spool is rotated, a lift rising container, another container drops. ?? Wound type according to the shape of the drum is divided into equal diameter hoist and hoist two kinds of variable diameter. Diameter reel and other simple structure, easy to manufacture, low price, have been widely used. When deep upgrade, since both sides of the rope length changes, the torque is very uneven. Early use of variable diameter hoist (cylindrical-conical drum), is now more balanced tail-rope. Environmental Safety Rules electric basket electric basket uses a floating equipment to enhance people in the use of the basket for construction work must strictly abide by the use of safety rules. ?? 1, construction or structure at the top surface of the support suspension mechanism bearing strength of not less than 1500 kilograms per square meter. The suspension mechanism when subjected to by top embedded parts, the safety factor of not less than 3 embedded parts. ? ?? 2, to provide power to the role of the basket must be 380V, three-phase five-wire grounded power source. ?? 3, prohibited the use of hanging baskets from the high-voltage lines in the 10M range. Under ?? 4, thunderstorms, fog, snow and wind speed greater than 10.8m / s (equivalent to gust 6) of the harsh climate, non-basket off the job. ?? 5, below the range if any road construction or channel must be set warning line or safety gallery at the bottom of the basket, and setting up clear warning signs and equipped with safety oversight personnel. ?? 6, should remove all prominent or obstacles in the basket off the job scope, fixed projections or the corner should set clear warning signs outside to open the window open during construction is strictly prohibited. ?? 7, when night construction, the construction site should have adequate lighting, workers, safety devices, electrical boxes and wire rope, life rope moisture, water and corrosion and other protective measures should be prepared. Construction basket in the job basket contingency plans in the construction work, as encountered in the following exceptional circumstances, should remain calm and take appropriate emergency measures. 1, the construction sudden blackout: construction basket in the job a sudden power outage, immediately turn off the power switch electrical box, to prevent accidents when the power is to be received after notification of the call on the power switch, and start working normally after inspection . Such as the need to return the ground after a power outage, while lifting both ends should enhance the downhill handle manual machines that suspension platform free skate to the ground. 2. Work steel Sishengyinsong shares, kink or hoist parts and jammed in the elevator were forcibly freed damage. Evacuation of construction workers within the suspended platform in ensuring the safety of the situation, sending the professional training of maintenance personnel to enter the suspended platform maintenance. First, the safety rope wrapped around both ends of the hoist mounting bracket with a tie clip to fasten safety rope ends. Then loosen the safety lock arm roller ends guard ring, rope and roller disengagement work, to make the two ends of the rope lock in lock state. 3, suspended platform raising and lowering process Release the button can not be stopped: suspended platform liters when down during and after the release button can not stop, you should press the red emergency switch on the electrical box door immediately, so hanging Emergency stop hanging platform. Then cut off the electric box power switch, check the contactor case, the contact surface grease to clean impurities, hands on the contacts can be restored to normal operation, close the power switch, use the manual method to suspension platform downhill to the ground for maintenance. 4. Working rope fracture: suspended work platform at one end of wire rope break, suspended platform tilted, inclined to a certain position when the safety lock automatically closed, the wire rope suspension platform is locked in a safe. At this time, the suspension platform construction should remain calm, non-run and jumping in the suspension platform, jammed emergency measures in accordance with their rope when lifting the machine for processing. 5, the suspended platform shall be horizontal tilt automatically locks the rope: suspended platform in the ascending, descending or end of the downhill course and a horizontal tilt to a certain range, the safety lock automatically locks the rope, it should immediately shut down, and then the electric box on The switch turned to the low-end platform, press UP button to lift the suspension platform to restore the level of low-end position, after the safety lock unlocked automatically restore the suspended platform to the ground, check and adjust the gap to meet the ends of the electromagnetic brake requirements; or check both ends of the rotational speed differences, such differences are significant should be followed by changing the motor.