Grinder price

Model Pricing Model Voltage (V) Power (KW) WN-200 220V or 380V 2.2KW WN-300 380V 5.5KW WN-400 380V 7.5KW WN-500 380V 11KW WN-600 380V 22KW grinder machine (stainless steel mill ) for the pharmaceutical, chemical, food and other industries use material crushing, crushing banned from flammable, explosive materials. Not suitable for crushing high oil content (such as sesame, walnut, melon seeds, rapeseed, etc.), the viscosity of the material, because of the high oil content and viscous materials can easily clog the screen. How it works: universal grinder produced by our company with high-quality 304 stainless steel, supporting national standard motors, mainly used in chemical materials, medicines containing roots, branches and massive class materials, a variety of food is not high oil content , whole grains and other hard, brittle materials. Relatively high-speed operation of the machine use activities and fixed gear tooth plate between the plate, so that was crushed by the tooth plate impact, friction and collision between the material and get crushed. Crushed material can be discharged directly from the grinding chamber, through the discharge port out of the general to go through the material after crushing cotton bags to collect the crushed material collected in the bag, the air from the bag of small perforations out, will not be powder discharge, which play no waste, no pollution effects. Particle size is determined by the switch to a different number of screens. The machine structure is simple, strong, smooth operation, the crushed material quickly and evenly, to good effect. This machine is all stainless steel material, inside the case (grinding groove) All gullet by precision machining to achieve a smooth surface, easy to clean, change the ordinary mill rough wall, easy to plot powder, hard to clean up the phenomenon, so that food, pharmaceuticals, chemicals and other production more in line with national standards, health requirements of GMP. Note: 1. The machine should be installed in an external power supply suitable machine power circuit breaker according to the purpose of the machine load is too large, the current is too large, automatically cut off power to protect the motor! 2. The machine has a special care to ensure that at work. 3. Crushed material particles should not be too large, in case of boring machine (ie machine speed because the load is too large to be significantly slower or passively stopped), it should immediately cut off the power supply. 3. If the particles are too big to be crushed, it should be universal after crushing crusher, and then smash the machine. ★ grinder (stainless steel mill dust) cooling unit Description: grinder, stainless steel mill dust, according to the special requirements of users and the particular material being crushed physical and chemical properties of water-cooling device can be installed. If the melting point of the crushed material is low, lower ignition, heated easily become soft, sticky, resulting in a decrease in pulverization effect can not be crushed or even cause a fire, explosion, which it is necessary to install a water-cooled grinding equipment on the cooling device. This machine is not suitable for crushing viscous material and high oil content of the material. Commonly used water-cooling unit is in the front wall of the grinding chamber and rear respectively install a water seal clip, the flow of water or well water continually flows into the rear wall of water pinch, and then flow into the front wall of water folder, and then by the former wall clip back into the rear wall of water discharged from the rear wall outlet. The purpose is to reduce the temperature of the water-cooling unit of the grinding chamber! ★ Tips: 1. Different seasons, different temperatures, different cooling water temperatures will produce different results. 2. Heat crush different materials produce different temperature was also different. 3. The lower the temperature of the water flowing into the water-cooling unit, cooling (heat) better. 4. Melting point of different materials, different ignition point, the user must be pulverized material have a full understanding and grasp. 5. The cooling device to install an additional reservation. 6. The water flowing into the cooling chamber, some pressure as low as possible as well, too much pressure will make the water infiltrated the grinding chamber, causing the material is immersed in water. Technical parameters: Model WN-200 WN-300 WN-400 WN-500 WN-600 Material No. 304 full stainless steel, 304 stainless steel full-resolution full 304 stainless steel 304 stainless No. No. Full Full 304 stainless steel voltage (V) 220/380 380 380 380 380 Power (KW) 2.2 5.5 7.5 11 22 Spindle Speed ??4200 4,200,420,042,004,200 fineness (mesh) 10-120 10-12010-120 10-12010-120 yield (kg / h) 10-120 30-200 50 -300 70-500100-700 Dimensions (mm) 480X520X1040 750X600 X1260 780 X700 X1350 800 X900 X1550 1200 * 1000 * 2000 Weight (kg) 75 180 260 320 400