Home
Products
Xinjiang anchorage supply carbon fiber plastic potting compound sealing glue stick steel carbon fiber adhesive glue
Xinjiang anchorage supply carbon fiber plastic potting compound sealing glue stick steel carbon fiber adhesive glue
Xinjiang anchorage supply carbon fiber plastic potting compound sealing glue stick steel carbon fiber adhesive glue
1. Introduction JL-31 high-strength two-component construction adhesive anchorage strength of composite resin adhesive, with a strong anchor, curing speed, simple construction, materials, and low cost. 2. Product Features ? Curing speed, reconciliation of rapid curing at room temperature ? Load faster on the building structure, and strong anchoring ? Heat resistance, room temperature, no creep ? Anti-aging, anti-media (acids, alkalis, water) performance ? Anti-welding and flame resistance ? Tightness, moisture resistance, resistance to shock ? Process performance can be -10 ℃ ~ +40 ℃ environment construction 3. Application ? A variety of building structure steel, screw implants ? Building structure reinforcement, reinforcement ? Building structural frame, shear wall anchorage ? A variety of devices based on a fixed ? Railways, highways, bridges, water reinforcement Extension ? Billboards, pipe tunnels, elevated roads and rails fixed noise 4. Curing time JL-31-type curing time Initial setting time of installation time based temperature curing time -5 ℃ -0 ℃ 30min 20min 5h 0 ℃ -10 ℃ 20min 15min 3h 10 ℃ -20 ℃ 16min 10min 2h ≥ 20 ℃ 12min 5min 1h 5. With the proportion of plastic With plastic glue and curing agent ratio: 20:1 6. Package ? In plastic drum, plastic, and curing agent united in a barrel packaging ? Min 15kg / group, and 5kg / Packing Group Two 7. Technical parameters Key Performance Indicators Compressive strength flexural strength performance capacity of vibration fatigue shear strength of adhesive strength Index 1.9-2.2 (g/cm3) ≥ 60Mpa ≥ 20Mpa ≥ 36Mpa> 800 million plastic / concrete C20 ≥ 7Mpa Rubber / clay ≥ 3Mpa Plastic / general bar ≥ 11Mpa Plastic / steel ≥ 16Mpa Install and load the data Level of reinforcement bar diameter (mm) hole diameter (mm) Anchorage depth (mm) design tensile strength (KN) standards for tensile strength (KN) Ⅰ 6 10 ≥ 80 5.9 6.6 Ⅰ 8 12 ≥ 120 10.5 11.8 Ⅰ 10 14 ≥ 150 16.5 18.5 Ⅰ 12 16 ≥ 180 23.7 26.5 Ⅱ 10 14 ≥ 140 23.5 26.5 Ⅱ 12 16 ≥ 160 33.9 37.9 Ⅱ 14 18 ≥ 190 46.2 51.5 Ⅱ 16 20 ≥ 220 60.3 67.3 Ⅱ 18 22 ≥ 270 76.3 85.2 Ⅱ 20 25 ≥ 300 94.2 105.2 Ⅱ 22 28 ≥ 330 113.9 127.3 Ⅱ 25 32 ≥ 380 147.2 164.4 Ⅱ 28 35 ≥ 480 184.6 206.1 Ⅱ 30 38 ≥ 590 211.9 236.7 Ⅱ 32 40 ≥ 650 241.1 269.0 Description:? I Grade Reinforced: fy = 210N/MM2 (design strength), fyk = 235N/MM2 (standard strength) ? II steel bar: fy = 310N/MM2 (design strength), fyk = 335N/MM2 (standard strength) ? Concrete strength C30, fuk, cubc, 150 = 30N/MM2, construction temperature: -5 ℃ - 40 ℃ ? Characteristic value of the safety factor does not take into account the relevant technical details please feel free to contact the Department of Engineering Technology: 8. Operating Process Planting bars, screw construction points: ? Drilling: drilling based on technical parameters ? Chiang Khong: a pump or compressed air and brush to clean drilling, clean and up to date ? Ingredients: Remove A, B component adhesive, uniform mixing with professional tools ? Note plastic: plastic with a good will gradually outward from the bottom of the hole into the hole ? Anchor: steel or screw to screw into the hole slowly ? Cure: Based on the substrate temperature, waiting for enough time to gel curing, to be fully cured gel load after install 9. Note ? To mix, thoroughly clean the hole, not touch the rod before cure is strictly prohibited ? Construction are required to wear gloves, masks, goggles, helmets and other protective equipment ? If you accidentally get on skin or clothing, used acetone to clean and rinse with plenty of water, food or if accidentally splashed into the eyes, immediately seek medical treatment 10. Transport, storage ? This product is a non-dangerous goods, transport of chemical building materials by the general ? No exposure in transit, rain, upside down or damaged packaging ? This product should be stored in a dark cool (5-25 ° C), dry warehouse, storage for 6 months Sales Tel:
Contact Detail
Company Name: | Shanghai Industrial Development Co., Ltd. Jian Lee |
---|---|
Employee Number: | |
Annual export: | |
Year Established: | |
Contact Person: | Mr. Chen Dongliang(Manager) |
Telephone Number: | 13918759739 |
Company Address: | Qingpu District, Shanghai, Shanghai, Shanghai, China |
Zip/Postal Code: | 201700 |
Find More Related Products
- Supply of the human body el..
- Supply Portable Needle Dete..
- ABB MCCB supply agent S1N12..
- In addition to static equip..
- Supply plastic CFRP anchora..
- The new force used forklift..
- Supply of art glass plate
- Supply depot anti-static eq..
- Supply antistatic ball, sta..
- DuPont 527UV supply POM
- Supply POM F20-02 Korean En..
- Heilongjiang anchorage supp..
- Supply of used equipment ne..
- Supply Desktop Needle Detec..
- Cosmetics packaging materia..
- ABB supplies a relay CR-U23..
- Account the supply Co54Cr9 ..
- Hurst MT24F01 supply POM Ge..
- Lacey Used Forklift Supply ..
- Supply bag
- Supply of chlorhexidine ace..