Steel mill pinion fitting specification is complete

Ball mill pinion material can be divided into: 35 silico-manganese, forged steel, 40 chromium molybdenum. Ball mill gear materials can be quenched and tempered steel (ie steel or carbon steel), or with a hardened steel (ie low-carbon steel or low-carbon alloy steel, the high speed and heavy-duty multi-quenched and tempered steel gears, gear surface using surface hardening, general hardness of HRC40-HRC55. For by the variable load or impact load gear, then carburizing steel. high surface hardness after carburizing steel after carburizing quenching, up to a HRC45 HRC60, having good toughness, so the tooth surface wear, pitting, and they can withstand the impact. ball mill pinion commonly used materials of high-carbon steel, but some use silicon, manganese, nickel, molybdenum alloy steel, in order to achieve it high tensile strength, usually a ball mill pinion gear than the hardness is lower. Material mill pinion is usually divided into 35 silico-manganese, chromium molybdenum 40, forged steel quenching etc. Different materials, their prices are not ... the same as each manufacturer according to their own circumstances, to choose different materials work environment mill pinion ball mill and the use of life is very important mill gear installation method mainly includes the following steps: Step one: with rubber wrapped half 3,5,8 ring first hole with a diameter of 36mm wire rope length over 10m2 root, with 10t chain guide, will maintain the level of semi-ring hung from CD pre-positioned on the ground across the eastern part of good wood, preventing contamination gear second Step three: half wrapped with rubber ring first and sixth holes with a diameter of more than 36mm 10m1 root length of wire rope, wear first larvae L, the sixth hole with a 10t chain guide, the semi-ring lift, a quarter moon shaped There are lubrication and no lubrication first half tooth hoisting way The third step: the semi-ring hanging onto the Ball Mill, seated in a semi-ring at each end of a 10t hanging chain guide, chain guide The other end hanging on the flange bolt holes simplified the chain length adjustment of the guide chain force Step Four: crane with three sets of 10t chain guide on top of two relaxation, while a tightening below, if necessary with crane hook loose, move, rotate the gear around simplified down until the gear recess obliquely about 45. So far, on the positive bolt holes, after penetration bolt, cranes, chain guide off the hook. There lubrication state No lubrication first half rotated to the bottom of the barrel tooth way Step 5: The other half of the ring gear with rubber wrapped first 3,5,8 larvae L, with a diameter of 36mm wire rope length over 10m2 root, with 10t chain guide , would maintain the level of semi-ring hung from CD pre-positioned on the ground across the eastern part of good wood, preventing contamination gear Step Six: Use rubber ring wrapped in the half of the first 3,6 hole with a diameter of 36mm wire rope length over 10m1 root , through the third hole, the sixth hole with a 10t chain guide, the semi-ring lifted a first quarter moon shape. Hanging onto Simplified adjustment with the chain in place, aligned bolt holes, bolts after wearing people , cranes, chain guide uncoupling how to replace the ball mill pinion adjustment: Regardless of which manufacturers of ball mill without any small or large mill pinion belong to the scope of the vulnerability of manufacturers in the ball mill pinion material... Good control, use manufacturers use reasonable under normal circumstances the use of a pair of ball mill pinion 5 - 8 years without any problems. Some manufacturers use 1--2 years are not uncommon. Pinion sided badly worn out surfaces can be used. Two faces were badly worn, must be prepared in advance. First, find a professional ball mill pinion outer diameter measurement, diameter, width, number of teeth. Then find a professional pinion ball mill pinion gear manufacturer order. Each manufacturer according to their own situation, choose different types of ball mill pinion and materials. Try to avoid using the ball mill pinion not only intend to replace. Thus affecting the production process because of the need 7-10 days under normal circumstances, a pair of ball mill pinion. When replacing the ball mill pinion fixed first, then find the ball mill cylinder centerline, the small gear on the launch pad, to find out the pinion centerline to centerline ball punctuation identify the centerline of the pinion parallel with the line, and then moved with the pinion gear carrier engaging position to adjust the size of the gap two centerlines gears. All ball accessories accessories by size of our own gear production process, absolutely authentic, standard size ball mill gear, ball spherical bush, a ball mill hollow shaft and other accessories are long-term stock. From the rough to the finished product to ensure the original factory goods, without intermediate links. And a variety of special materials can be customized according to customer requirements, not only to ensure the relevance and quality of the ball mill pinion, but also to ensure the price of concessions, so I plant to buy ball mill pinion gear, ball spherical bush, a ball mill hollow shaft Accessories product is your good choice. ◆ Contact: (Mr.) ◆ Tel: 0516 - 83102632 ◆ Fax: 0516 - 83102632 ◆ Address: Xuzhou Quanshanqu Huai Haixiluma Hill Industrial Park ◆ Business Line: 15996966359