BobrickB-7120230V the disabled wall-mounted hand dryer

Action: No-touch operation: electronic sensor automatically when you open the machine, hands in the path of the air outlet and the whole held sensor. Double outlet airflow provides a comfortable hand drying roundabout circulation. Drying time is less than 25 seconds. Remove from the sensors and stations in the hands of the path. Dryer works only actual drying hands, which saves energy and operating costs. Electronic sensor will automatically shut dryer off 1-1 / 2 minutes turned on, a inanimate objects if after, such as tape or chewing gum, is placed across the air outlet opening. After inanimate object is removed, electronic sensor automatically reset and dryer is working properly. 1-year limited warranty - 1 year warranty in addition to Bobrick, Bobrick extends a limited one-year warranty from date of purchase of the model for the B-7120 and B-7128 hand dryer all parts, motor brushes, in addition to the original the owner of the plant process or material defects in normal use and maintenance, installation of the unit. Motor brushes are necessary from the date of purchase for one year. This warranty is limited to the choice repair or replace defective parts Bobrick. Please refer to the installation instructions, the form number 712-69, for full details. Specifications: Surface Mount hand dryer should have 22 or galvanized steel sheet and the exposed surface type 304 stainless steel with # 4 satin polish vertical lines (B-7128) or 22 of low carbon steel galvanized high-gloss white epoxy paint (B-7120) includes a black plastic trim and UL94-5VA. Slim profile cover project should not exceed 4 "(100mm, office) comply with Accessible from washing the face wall design guidelines (including ADAAG in the US). Unit shall be equipped with double outlet for (less than 25 seconds) to spin the hand drying provide airflow The flow loop should be 1/7 horsepower motor, the drive shaft end in universal fixing elastic band sealed ball bearings and self-lubricating sleeve bearings nondrive end; equipped with automatic thermal overload switch the heating element should be located in the outlet side of the fan will. hot air without hot spots, it is inaccessible saboteurs, and automatic thermal overload protection switch. Electronic sensor automatically turns dryer on when hands in the path of the air outlet and the entire sensor was when the dryer will automatically shut down, hand removed. the sensor will automatically shut dryer off approximately 1-1 / 2 minutes machine is turned on, if an inanimate object is connected across the air discharge outlet. After inanimate object is removed, electronic sensor automatically resets and the dryer will run correctly The unit should be in accordance with cULus Listed, and / or VDE certification, CE certification unit shall comply with the EU directive "Restriction of Hazardous Substances" (ROHS), for the production of non-use requirements of certain hazardous substances in electronic products shall through the limited 10 - year warranty period, unless all parts motor brush motor brushes should be protected to ensure that the date of one year from date of purchase materials: cover - 22 galvanized steel sheet and the type of surface exposure of 304 stainless steel with # 4 satin polished vertical lines (B-7128) or the 22nd of low carbon steel galvanized high-gloss white epoxy paint (B-7120) and comprises UL94-5VA black plastic trim and side panels. Cover with a unique design of dual outlet Intake equipped with anti-riot gas grill cover project from the wall of no more than 4 "(100mm) and is fixed to the mounting base with two vandal recessed hex screws mounting base - 20 (1.5 mm), chrome steel with four 0.236 '' (mm) mounting hole diameter. Motors - General, 1/7 hp, 8000 rpm, the resilient mounting. Sealed ball bearings at the shaft end and self-lubricating sleeve bearings nondrive end. Equipped with automatic thermal overload switch. Fans - two balanced, double inlet centrifugal fan mounted on the motor shaft; airflow above the heating element 71 cubic feet. Heating element - the double helix Nichrome heating elements are mounted in mica frame and automatic thermal overload protection switch. Heating elements, hot air is not hot - inaccessible to vandals. Electronic Control - Infrared sensor automatically when you open the machine, hands in the path of the air outlet and the whole held sensor. Remove from the sensors and stations in the hands of the path. Electronic sensor has automatic shutdown after about 1-1 / 2 minutes machine is turned on, if an inanimate object is placed across the air outlet. After inanimate object is removed, electronic sensor automatically resets and dryer work Installation: Wall Preparation: find a wall mounting base using the supplied templates. For brick, stone and concrete wall drilling 40.315 "(8 mm) hole provided to meet Wall 0.315" (8 mm) × 1-1 / 4 "(45 mm) of and screws # 10 (4.8 mm) × 2" ( 50 mm) long. See details template wall plug and screw mounting. For plaster or dry wall construction, provide covert support to comply with local building codes and four # 10 (4.8) round sheet metal screws or 3/16 "(5 mm) wall bolts (not supplied) Provides recent switchboard Electrical Services dryer installed base of in accordance with local electrical codes.