Single-barrel engraving machine Vacuum cleaner vacuum cleaner accessories Mudanjiang

Engraving machine cleaners commonly known as (industrial dust collector, mobile-type vacuum cleaner bags, advertising engraving machine cleaners, wooden furniture cleaners), divided into single-barrel vacuum cleaner with a double barrel vacuum cleaner is widely used in various wood factory, furniture factory, wood products, pharmaceuticals, food, electronics, chemicals, instruments, precision machinery, metal, plastic, leather, shoe factories and other large amount of dust production environment. Portable vacuum cleaner bag engraving machine works: When dust and gas from the entrance into the mobile vacuum cleaner bags by diversion tube into each cell compartment, under the action of the deflector, large dust particles directly into the hopper after the separation, remaining dust with the air evenly into the various compartments of the bag filter area when the gas passes through the dust bag, namely dust adsorbed on the bag, and was excluded from the purified gas inside the bag. Mobile engraving machine vacuum cleaner bag outstanding characteristics: mobility, randomness is good, cleaning effect of good, for dust points more suitable environment; it can be implemented arbitrarily control the points machine; avoid waste of resources and affordable electricity, vacuuming. good effect. Engraving machine maintenance and repair a vacuum cleaner, vacuum cleaner fan engraving machine to regular inspection, maintenance, grease lubricated bearings require filling once a week; always check the tightness of the belt when the belt is too loose discovered motor tensioning screw can be adjusted to moderate So far, at any time to check whether there is something attached to the fan, if so, should be cleaned, so as not to fan vibration and damage, affecting life. Second, the engraving machine cleaner before stopping in front of the first outlet duct is closed, leaving behind 2-3 outlet, in order to remove dust residue in the air duct, and start from the back, off a back vent, open a front outlet, and so on, Wind will concentrate duct residue cleaned from the back to front, so as to avoid blocked ducts. Third, the engraving machine Vacuum cleaner dust bag storage need to periodically clear the way checks cleared at the cleaner vertebral ash outlet is blocked, if there should be cleaned immediately to avoid congestion caused by the central tube ran dust. Cause engraving machine cleaner fan operation failure resulting in a fan severe vibration: 1, the fan shaft and motor shaft is not parallel to the pulley groove dislocation. 2, casing or impeller friction with the air inlet. 3, the base is not strong enough or rigidity. 4, impeller impeller deformed or loose rivets. 5, the impeller shaft and the shaft with loose plate hole. 6, chassis, bearing and bracket, bearing and bearing cap bolts and other loose. 7, fan inlet and outlet pipe installation poor resonance. 8, there is fouling leaves, dirt, leaves worn, the impeller deformation, shaft bending so unbalanced wheel. Second, the bearing cap temperature too high: 1, bearing housing vibration intense. 2, poor quality lubricants, deterioration or contain dust, sand, dirt and other impurities or insufficient amount of filling. 3, bearing cover, seat connection bolt tightening force is too large or too small. 4, the shaft with rolling bearing installation skew, both before and after bearing a different mind. 5, bearing damage or bend the shaft. Second, the motor current is too large and the temperature is too high: 1, boot into the inner outlet duct damper is not closed. 2, the motor input voltage is low or single-phase power supply. Affected bearing intense vibration. Portable vacuum cleaner bag engraving machine Cause Failures and Failure Remedy 1 fan vibration has attachments 2, bearing damage and clear is 2, replace the bearing fan noise largest bearing damaged Replace bearings fever lack of lubricant lubricating the fan added Under vertebral export agent center tube running gray duct blockage cleared ignition spark Clear nail polish workpiece motor and dust inside the duct hot on the workpiece 1, the motor is attached to the surface difficult to heat the surface of the foreign body causing the motor 2, motor bearings missing oil stuck 1, to eliminate surface deposits ventilated 2, replace the motor bearings portable vacuum cleaner bag engraving machine parameters: Model Power (kw) air volume (m3 / h) suction outlet (a) dust bag (pcs) filter bags ( pcs) MF9022 2.2 2350 Ф100 × 3 Ф480 × 900 × 1 Ф480 × 1100 × 1 MF9030 3 3150 Ф100 × 3 Ф480 × 900 × 2 Ф480 × 1100 × 2 MF9040 4 4450 Ф100 × 4 Ф640 × 1000 × 2 Ф640 × 1200 × 2 MF9055 Our long-term supply: 220V single barrel advertising engraving machine cleaner / double barrel 3KW / 4KW 380V power engraving machine supporting the vacuum cleaner and another cover sales: diameter 80MM 100MM 125MM welcome to contact us to buy! Tel: 15165176816