Ssangyong Porcelain leveling agent porcelain seam sealant US joint agent true porcelain glue factory outlets

Manufacturer: Albert Harbin Ssangyong Technology Development Co., Ltd. (www.shuanglong.mobi) Product Category: US joint agent wholesale prices tile US joint agent, tile adhesive, tile adhesive, the US joint agent manufacturers, the US joint agent Manufacturer US joint agent effect. Porcelain joints agent, porcelain leveling, true porcelain US joint agent, true porcelain glue, sealant use: for ground cracks decorative tiles, mosaics, stone, swimming pools and other materials. Construction method: 1, clean the tile gap, according to the 2: 1 ratio of two US sewing AB agent into disposable cups, adding an appropriate amount of toner, and then stick mixing evenly (low speed agitation), about 30 seconds about. 2, take construction plastic beak vial, the disposable cups plastic beak of material poured into the vial, capped to construction, pay attention to force uniform construction (vial posted flat beak and tile gap), can be less than 0.5mm tile surface to prevent liquid outflow gaps. 3, at room temperature (25 degrees) surface dry three hours non-stick dust, 1 to 2 days completely solidified, can not wipe until completely solidified, fingernail inspection surface hardness to understand is completely solidified. Note: 1, this product can not be used with similar products in the market mix. 2, beak vials construction, if the need to fight about 1mm seam tile, please a few mixed plastic, probably about half a bottle, because the mix will occur more heating phenomenon may not finish it thickens, please adjust according to their own experience. 3, the construction process if the overflow surface of the tile joints agent of the US legislation that cleaned with a cotton swab. 4, the case of a new seam sealant does not fill the gap, with white sand-free sealant caulk, suggested large plastic scraper (wallpaper scraper) caulking, fill out without dry immediately with a push rod extrusion seam depth 2mm below about 3mm deep groove. 2mm or more of 2mm deep groove, caulking pressed not have loopholes, do not wait sealant dry, you can immediately gluing. Product Storage: at room temperature storage conditions, the retention period from the date of production for 18 months. First, the product features 1, high hardness. After curing hard like ceramics. 2, high brightness. Gloss Gorgeous, beautiful eye-catching. 3, will not shrink or sag. Completely avoid the one-component US joint agent easily shrink collapse, the formation of defects recess. 4, no mildew, the same black. From the fundamental solution to the problem of black mold the existing tile grouts. 5, the bonding firm, do not fall off. US joint agent itself is a special kind of plastic material and the substrate after curing firmly bonded together. 6, abrasion resistant blisters. US joint agent has excellent adhesion, it can be used in the bathroom. 7, acid and alkali resistance erosion. Ten anti-aging, maintain excellent properties. 8, excellent stain resistance. This is excellent new material gold unique product features. 9, simple operation, easy DIY. Do not stick masking tape paper these cumbersome procedures. 10, environmentally friendly products, non-toxic, maximum protection operating health of workers. 11, suitable for a very wide range of substrates. Sealant can be used for bonding ceramics, stone, glass, mosaics, ceramic stone, cement, concrete, wood, metal and other different products, sealing, plugging fixed. All kitchen, bathroom, living room, tiles and other decorative landscaping where needed. Really high-end atmosphere on the grade of the product, with excellent visual beauty! Third, the construction step 1, the tile gap must be filled out in advance with common sealant, reserved or gouged with a knife 1 ~ 2mm in depth, and clean water and clean the surrounding gap, oil, dust and other debris. 2, the United States and sewing treasure A, B two components in a 2: 1 ratio corresponding to the scale of the beak into the bottle. 3, corresponding to the color of the ceramic powder in accordance with 10% to 15% by weight was added to the bill bottle (a small spoon per 20 ml powder, spoon supplied) and stir evenly. 4, according to a 45-degree angle beak bottle bevel cut out, the discharge port should be less than the slot width. 5, uniform compression along the tile gap beak bottle construction. Fourth, note: 1, A, B groups were mixed after the required operation is completed within 30 minutes. 2,25 degrees lower temperature for 2 hours surface dry, 24 hours to fully cure, the higher the temperature, the faster the cure. 3, if the construction of an overflow, namely with a towel can wipe or scrub with alcohol. Use a knife to shovel out after curing. 4, stick to the hands of available soap or detergent cleaning, the contact must wear rubber gloves, long time. 5, no exposure, freezing, away from children, away from the fire, sealed, shelf life of 18 months. V. Application of 1, tiles, tiles, tiles, antique tiles, ceramic stone, mosaic, concrete tiles, such as caulking, landscaping. 2, stone plates, glass, aluminum panels, fire boards, organic board, sun panels, wood floors, stainless steel, all kinds of metal sheet plate seams. Sixth, the construction in the amount of the slit width 2mm, construction of 350 m depth can at about 1mm per kilogram, low cost of ownership. (Product packaging specifications: A / B two components, 0.85KG.) Chun of the United States joint agent is A, B two component reactive beauty stitch seams, caulking nanomaterials products. Exterior color, delicate uniform paste, no odor, decorative effect is extremely strong. [Features] 1. With a waterproof, impervious, non-stick characteristics of the oil, the real never dirty tile joints black. 2. New Material: It is made of high-grade new high-tech polymer and pigment, which is different from white cement, colored sealant (grouts) (dry powder cement material + low-grade pigment) is mainly composed of an inorganic material, he is the new high-tech polymer materials + high-grade pigments and special additives fine formed. 3. Easy and convenient: take AB ratio can use the same amount into a color after stirring. Engineering AB large area can be stirred into the air hose, the application 4. The decorative effect is particularly strong with a glue gun, rich colors, natural and delicate, with shiny, do not fade, to wall and floor to bring a better overall effect (on the market The sealant dull dull color, color is limited). 5. Paul. China Building Materials Certification Center, free of harmful substances. Manufacturer: Albert Harbin Ssangyong Technology Development Co., Ltd. (www.shuanglong.mobi) Product Category: US joint agent wholesale prices tile US joint agent, tile adhesive, tile adhesive, the US joint agent manufacturers, the US joint agent Manufacturer US joint agent effect. Porcelain joints agent, porcelain leveling, true porcelain US joint agent, true porcelain glue, sealant use: for ground cracks decorative tiles, mosaics, stone, swimming pools and other materials.