Signs stamp coder - copper and aluminum iron plate surface of a code

Features: How it works: The steel dial induction hardening process in the external force (hand pressure or a rubber hammer drop), engraved on the metal plate out of a certain depth (0.1-0.3MM deep) letters or numbers , marking the location, word spacing, line spacing by specialized mechanical system stepless adjustment; different character height by replacing dial achieved the desired letter or number rotatable dial for easy replacement of the word. Print Size: 180MM * 135MM printing characters: uppercase letters, Arabic numerals, simple symbols font size: 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm Print speed: about 2-4 characters / 10 seconds Description: A, signs The display method shown signs placed by the work surface left position, with signs and magnet clip without loosening the pressing plate. B, handling the word of the first round with the word wheel wrench to remove the word wheel nut locking plate, choosing the right word round, and put on the character wheel lock nut, align pointer. After C, print and display good starting position adjustment plate, disengage the clutch lever, turn the hand wheel spacing and kerning hand wheel, make a character wheel alignment print frame just above the position locking the carriage, release the clutch handle, pressure activated a few kerning feed handle kerning calipers can be seen on the density of the feed (with hand wheel and adjust the kerning kerning) depresses the clutch, turn the hand wheel, release the clutch lever back to original with the palm slap rubber parts, after pressing the feed handle kerning, enables the printing. Routine maintenance A, the machine should be kept dry, clean and avoid internal parts corrosion, can regularly add adapt lubricating sliding surface to facilitate easy operation, no oil leakage as well. B, should avoid rotating character wheel printed directly on a countertop, causing uneven countertops, affect the future results, disuse should remove the word round. C, in adjusting the print start position, be sure to release the clutch lever, such as mandatory fast-moving hand wheel moving table, it will operate the drive belt to make receipt of common faults and feed adjustment Symptom Cause denial or failure to exclude Fault type symbol on top of each word neatly around 1. round zandong 2. Signs loose unclamped 1, locking the carriage, tighten the word wheel nut 2 again pressed uneven signs a receipt, receipt feed under did not handle the pressure place 2, the belt is too loose or show wear 1, 2 lower handle pressure is not in place, adjust the belt tension or replace Wuxi Brook manual signs nameplate machine manufacturers (www.wuxidaiaoji.com  ) specializing in the production of manual metal Standard (Ming) licensing parameters Printer Name: Manual Metal Mark (Ming) licensing parameters marking machine, metal marking machine manual metal standard (Ming) licensing coding, standard (Ming) licensing embossing machines , Standard (Ming) licensing embossing machine, standard (Ming) licensing parameters cutting plotter, Standard (Ming) licensing smashing machine, manually stamp machine. Manual and automatic two advanced operators, manufacturers welcome all the friends wholesale and retail agents. Features; handsome in appearance, simple operation, long life, good print quality, low price, was recognized by the SMEs, Electrical and Mechanical Services Department and other business owners, which are widely used in valves, pumps and other mechanical and electrical appliance industries manual... signs nameplate engraving machine different numbers and letters on the metal plate is a lot of mechanical and electrical products manufacturing enterprises often work to be done. The traditional approach to stamp percussion, often resulting in skewed font, kerning uneven shades, signs deformation and other issues, and low efficiency. How to improve the quality of signs, especially in terms of export product label is very important. Computer stylus cutting plotter though it can imprint, but its high price allows some of the small number of SMEs prohibitive signs. Wuxi Brook manual signs nameplate machine manufacturers on the basis of export products by improving the design and production of KT-BP02-type sign cutting plotter completely overcome the above drawbacks. Since the products are small, light weight, easy operation and smart, print neatly and writing clear and uniform, and low prices, a product launch to get users. Transaction integrity, the future, we will be high quality products and good service, welcome all friends to visit our company guidance, to discuss cooperation. Purpose: The parameter changes on the metal plate engraving: If the specific type, date, batch number, serial number, serial number and so on. Typical applications: mechanical, electrical, pumps, valves, automobile, electrical appliances on all types of aluminum, copper, stainless steel, plastic nameplate. Production background: The traditional stamp percussion way, often resulting font crooked, shades and inefficient. A long time, how to improve the quality label has plagued industrial enterprises engineering staff. Pneumatic marking machine (aka: computer stylus cutting plotter) even though it can imprint, but its high price allows many signs of a small number of SMEs prohibitive. I plant designed and developed signs parameters smashing machine (clap mechanical) fully addresses the deficiencies and low prices. Launch of a product on the market has been widely recognized.