Guangdong resin tank fiberglass resin tank without gallbladder bile resin glass steel pipe

Water Treatment Equipment Co., Ltd. Jinan Beret resin tank Description softening resin tank three main categories, a fiberglass liner without glass steel liner 2 2 3 stainless steel tank steel reinforcing material 1. E-glass fiber rovings should be consistent with JC / T277 provisions alkali fiberglass rovings should be consistent with JC / T278 2. E fiberglass roving shall comply with JC / T281 3. fiberglass chopped strand mat and carpet surface should be accompanied by resin systems chemistry invasion of compatible agent. The fiber surface may also be felt or other organic materials. 3 Technical Requirements tank usually consists of the inner surface layer 1, the inner strength layer and an outer surface layer consisting of four layers. It can also be taken in accordance with the requirements of other layered structure; the wall thickness of the tank changed in accordance with design requirements under the premise. 2. The inner cylinder surface layer, the inner layer of the resin content depending on the storage medium of change. 3. The inner wall of the taper angle exceeds 1 ° 4. Under loading conditions, the tank wall to allow the ring to strain not to exceed 0.1% 5. filament wound layer, taking a spiral winding angle of 80 °, the axial tensile strength of not 1. Vertical head lower than 15MPa tank can be ellipsoidal head, flat shape and conical head up and down in different forms can also be used in combination. Horizontal tank is oval head 2. Head strength layer injection, hand burnt-based, supplemented by the winding envelope: surface mat, chopped strand mat and woven roving primary placement, the bed joint should be staggered width of not less than 60MM. tower access width of 30MM. resin mass content of not less than 40% 3. Vertical storage tank when the ground, the bottom of the corner radius of not less than 38MM, with a flat bottom thickening decreasing tangent corner strengthen The minimum thickness zone of the structure and the thickness of the cylinder head and. 1. Supports horizontal tank saddle seat number less than two, saddles can also be steel, cast iron, concrete or glass hand burnt steel production 2. saddle bag angle of not less than 120 °. Saddle arc and storage tank outer garden consistent distance between the saddle 3. any two cylinder nominal diameter of not more than 1.5 times the 4. flat-bottom tank using planar concrete foundation. Soft cushion or pad 200MM thick sand cushion 5. oval head tank may be fiberglass or resin concrete legs under the seat on spherical bearings. Contoured seat and leg cushion should fit 6. aquarium tank bottom and leg base junction can add glass or steel rims rib lugs. Strengthening aid 1. The horizontal tank should be strengthened to help the tank according to the selected aspect ratio is reasonable, it can be set up in the tank to help strengthen internal or external. Saddle area should be set up to strengthen co-thickening, and its thickness less than the thickness of 2/1 the width of not less than 1.3 times the width of the holder. Open side should be level 2. No cover vertical tank ribs. 3. Strengthening ribs with chopped strand mat and fabric on the cylinder alternately winding, outside wrapped roving compaction. Other materials may also be used to strengthen the rib composite material. 1. The upper portion of the exhaust pipe and tank overflow pipe exhaust pipe and the atmosphere should be set free Unicom. The minimum diameter of the exhaust pipe should be greater than expected out of the tube diameter. 2. The tank should be set overflow pipe, with a diameter greater than the diameter of the feeding tube. Anchoring device for the tank at the time of installation and operation, in particular, parallel to the bottom of the tank must be provided with a fixed anchoring device basis. 2. The anchoring device is not secured to the tank 4 softening tank specifications Model Specification editor on opening lower opening recommend flow 818 200 × 450 2.5-inch non 0--0.2 835 200 × 875 2.5-inch non 0.2--0.5 844 200 × 1100 2.5 inch no 0.2--0.5 1035 250 × 875 2.5-inch non 0.5--1 1054 250 × 1350 2.5 inch no 0.6--1.5 1018 250 × 450 2.5-inch non-0.2 ------ 0.5 1252 300 × 1300 2.5 inch no 1.6--2.2 1354 325 × 1350 2.5 inch no 2--2.5 1465 350 × 1625 2.5 inch / 4 inch thread without 2.5--3 1265 300 × 1625 2.5 inch not 2.0 ----- 2.5 1665 400 × 1625 2.5 inch / 4 inch thread without 3.2--4.5 2162 525 × 1500 4-inch 4-inch screw thread 4.5--6 2472 600 × 1800 4-inch 4-inch screw thread 6.2--8.2 3072 750 × 1800 4-inch 4-inch screw thread 7.2 - 12.2 3672 900 × 1800 4-inch 4-inch screw thread 13.2-16.2 4272 1050 × 1800 6-inch flange 6 inch flange 17--23 4872 1200 × 1800 6-inch flange 6 inch flange 22--27 4896 1200 × 2400 6-inch flange 6 inch flange 28--38 6096 1500 × 2400 6-inch flange 6 inch flange 38 ----- 55 7296 1800 × 2400 6-inch flange 6 inch flange 55 ----- 80 8096 2000 × 2400 6-inch flange 6 inch flange 80 ----- 100