Softened water processor

Shanghai Xena is a set of automatic softened water processor development, production, manufacture, sales and service in one of the production-oriented enterprises, long-term commitment to automatic softened water processor, boiler water softening equipment, recycled water softening equipment, Central air conditioning water softening equipment, electronic water processor, next to the water processor manufacturing, has accumulated a wealth of equipment manufacture, project construction experience, spring special company to provide project planning, consulting services, planning and design, manufacture and installation, training, maintenance a full range of services. Softened water processor mainly by imported multi-way valve (Pentair, Tuzu, FLECK, etc.), softening resin regeneration salt box, regeneration salt valve, resin filtration tanks, piping and other sets of components. Xena softened water processor can soften the anti-washing, absorption of salt and slow wash, quick wash, salt water tank and so the whole process is automatic. The presence of calcium and magnesium ions in water is the main cause of the formation of scale when the water temperature changes. The basic principle of demineralized water processor: automatic softened water processor sodium form strong acid cation resin raw water calcium and magnesium ion substitution out by the water softening desalination equipment treatment may be directly used as boiler feed water steam . The chemical reaction is: 2RNa + Ca2 + (Mg2) = R2Ca (Mg) + 2Na +. When the resin adsorption to a certain amount of calcium and magnesium ions must be regenerated after - with saturated brine resin to resin in the calcium and magnesium hardness ions displace restore soften exchange capacity of the resin, and waste discharge. The chemical reaction is: R2Ga = 2RNa + Ca2 +. Softened water processor regeneration process includes: 1. Backwash: the device to work for some time, it will intercept a lot of raw water to bring the dirt in the upper part of the resin, after the removal of these contaminants, the ion exchange resin to fully expose the regeneration The effect can be guaranteed. Backwash process is the water washed into the bottom of the resin, the outflow from the top, so you can put the top block down the dirt away. This process usually takes about 5-15 minutes. 2, an intake of salt (renewable): Coming resin tank brine injection process, conventional equipment is utilized in salt brine pump, automatic equipment is built by private jet to saline inhalation (long as the water pressure to a certain available). In actual operation, the brine flows at a slower pace than simply resin regeneration with brine resin is good, so is the use of saline water softening equipment slow flow through the resin regeneration, a process that normally takes 30 minutes of actual time is good enough salt. 3, the slow rinse (replacement): After the salt water flows through the resin, with raw water at the same flow rate slowly resin salt rinse the entire washing process is called slow, since the washing process is still a lot of functional groups calcium and magnesium ions are sodium ion exchange on the basis of practical experience, the process is the main process of regeneration, so many people will this process is called substitution. This process is generally the same time with the absorption of salt, which is 30 minutes. 4, quick rinse: In order to thoroughly rinse the salt residue, to be used with a flow rate close to the actual work, the resin is washed with raw water, final effluent of this process should be the standard soft water. Under normal circumstances, quick rinse process is 5-15 minutes. Xena boiler water softening equipment Specifications: Power: 220V / 50Hz power: 10-35W water production (single): 0-50m3 / h Working pressure: 0.2-0.5MPa Operating temperature: 2-50 ℃ Water Hardness: ≤8mmol / L Water hardness: ≤0.03mmol / L Procedure: Automatic Program Control Body material: high-strength plastic or lead-free copper alloy tank material: wrapped fiberglass or corrosion within the steel and stainless steel control: time type and flow type or No power hydraulic-driven layout: a single tank or tank parallel regeneration mode: downstream / upstream regeneration Interface Type: pipe thread / ABS flange ionic resins: strong acid cation exchange resin regeneration water consumption: ≤2% × water yield salt consumption : ≤160g / l Installation conditions: the basis of need alone device, generally flat concrete floor can, within the range of one meter around the unit should be located drains or drain.