MS-70 / MX-50 / MF-50 / ML-50

Product Description Japanese A & D to a new design concept, superb technology to produce high-precision rapid moisture analyzer, it is simple, easy to observe and its excellent performance fully used in food, tobacco, pharmaceutical, oil, paper, feed , chemicals, coatings, mining, environmental protection, geology and other industries to do a quick determination of moisture content of materials, while meeting the solids, granules, powder, jelly and liquid water content measurement requirements. Features: ● innovative SRA technology, rapid and uniform halogen lamp heater with straight tube halogen lamp and uniquely designed SRA (secondary radiation assist device) emitters to reduce measurement time, the formation of rapid and uniform heating. ● High accuracy SHS rapid and sensitive properties using load cells, making very little sample at high precision weighing can get a very accurate determination of moisture content. ● using sodium tartrate dihydrate sodium tartrate dihydrate as a standard measure to check the accuracy of the moisture content is 15.66% with a stable water content + 0.3 / -0.1 chemical substances, so the most reliable for the accuracy of inspection, measuring instrument supplied by reference value. ● heater temperature calibration (MS only / MX) Optional temperature calibrator, calibration result can format output for GLP, GMP, ISO's. ● Standard WinCT-Moisture software (MS only / MX) for real-time graphical display WinCT-Moisture software is a graphical display designed specifically for water content analysis software that can show changes in the moisture content measured graphics, and can so graphic, to set measurement procedure different samples by computer-assisted analysis. ● measurement procedure, measurement results memory function can store up to 20 groups of measurement procedures, at any time call different measurement procedures for determination of moisture content depending on the sample, and therefore both fast measurements and avoid setting operation error (MF store up to 10 groups, ML store up to 5 groups). Measurement results can be stored in 100 groups (MF 50 group, ML 30 groups) and through the computer or printer output. Completely avoid human error. ● comply with GLP / GMP / GCP and ISO standards, with date / time, ID, calibration data and test records output capable of calibration data and output measurement data recording, quality management and certification to meet the demand. ● standard RS-232 interface and two-way communication or PC connected to the printer. ● large screen display easy to observe fluorescence clear measurement procedures, set value, moisture content change rate, measurement status, data number and other important information at the same time clearly displayed at a glance. ● Easy to operate components designed ergonomic handle plate to avoid burns when generating the sort of unexpected hot sample was placed in or taken out, wing-shaped handle so the heated lid is easy to open and close. ● low maintenance costs to ensure that users do not need to replace the halogen lamp is disabled, a small room with a protective easy to clean (halogen lamp life of about 5000 hours) ● five measurement procedures Standard Mode: By setting high, medium and low measurement accuracy Automatic completion of the measurement. Automatic mode: When the moisture content is less than a set ratio change automatically when the end of the measurement. Quick Mode: In order to achieve rapid determination, before three minutes using 200 ℃ heated start and then complete the measurement The automatic settings. Timing mode: By setting the duration to complete the measurement. Manual mode: by pressing the button to start and stop operation of the measuring process. ● four drying procedures Standard Drying: After starting to heat up directly to the set temperature. Asymptotic Drying: After a preset time and gradually raised to the set temperature. Drying step sequence: phases with different temperatures according to the time. Rapid drying: 200 ℃ rapid heating using the heating continued according to the set drying temperature after 3 minutes. By any combination of the measurement program and drying procedures can fully meet the requirements of different samples to the assay. Model Range X precision MS-70 71g x 0.1mg MX-50 51g x 0.001g MF-50 51g x 0.002g ML-50 51g x 0.005g Standard Accessories ● tray (MS / MX / MF 20, ML 10 a) ● disk handle (MS / MX / MF has two, ML have a) ● tweezers, spoon and sample test specimen (sodium tartrate dihydrate 30g) (MS only / MX / MF) ● CD-ROM (MS / MX is WinCT-Moisture, MF is WinCT) ● MS / MX with RS-232 line, ● ● Dust film show the film (MS only / MX / MF) ● User's Manual ● Quick Reference Card ● Power cord ● fuse two Options: ● AX-MX-31 tray (100) ● AX-MX-32-1 glass fiber sheet (100) ● AX-MX-32-2 glass fiber sheet (100) ● AX-MX- 33 test sample (30 g sodium tartrate dihydrate 12) ● AX-MX-34 halogen lamp ● AX-MX-40 RS-232 cable ● AX-MX-41 calibration weight (20 g, OIML) ● AX -MX-43 Temperature Calibrator (MS only / MX applicable) Japan A & D electronic balance (100% in Japan) distribution prices can call dwell * Service:! With original machine number, one year warranty and lifetime maintenance (Chen. QQ: 1805987165 PT: 13715362422 TEL: 0755-82233355)