Guangyuan, Sichuan Guangan region with UCG-3011-S intelligent capacitive level meter

Product description: UCG-3011 intelligent capacitive material (liquid) level meter is the use of advanced radio frequency capacitive sensing technology, combined with industrial range measurement system for temperature drift compensation is made. It addition to inheriting traditional advantages Capacitance (liquid) detection technology, but also to solve the traditional Capacitance (liquid) level meter measurement system is difficult to overcome large temperature drift, poor detection of linearity, resolution of defects and poor. It can be applied to the measured medium insoluble component relatively stable medium level measurement and dry powder, pellet level measurement in various industrial environments. The product by the National Instruments explosion-proof safety supervision and inspection station (NEPSI) certification. Intrinsically safe explosion-proof mark ExiaIICT6 / T5, available for the respective explosive dangerous places. Principle of operation was later (liquid) to measure changes in its exploration of the relationship between changes in capacitance proportional pole generated by the detected change in capacitance measurement system temperature drift compensation, through a dedicated mode system software arithmetic processing, output and physical (liquid) level change is proportional to the two-wire 4 ~ 2 0 m A analogue current loop and four SPST (NO) solid state relay contacts. Technical Features 1, two-wire current loop, current loop isolation and measuring systems; 2, the measuring system automatically compensates for temperature drift; 3, simple two-point calibration; 4, the CE certification of good electromagnetic compatibility characteristics; 5, continuous measurement Level, level, interface; 6, a very excellent linear measurement, resolution smaller units of measurement; 7, low power consumption, no moving parts, sophisticated technology guarantee; 8, high temperature, high pressure, highly corrosive; 9, Chinese operating environment, relaxed setting, with self-diagnostics. Technical Specifications Operating voltage: Maximum: 30V minimum: (when CAP-3011-R, output 3.5mA) 18V 15V CAP-3011-S, when output 3.5mA) 10V (22mA when output) Current loop: two-wire 3.5mA ~ 22mA fault alarm current: 3.5mA or 22mA isolation performance can be set: Measuring systems and current loop isolation Explosion levels: ExiaIICT6 (-40 ℃ ~ 70 ℃) ExiaIICT1 ~ 5 (-40 ℃ ~ 85 ℃) Explosion parameters: Power Input: Ui = 30V, Ii = 100mA, Pi = 0.75W Ci = 100pF, Li = 10uH solid state relays (n): Ui = 30V, Ii = 100mA, Pi = 0.75W Ci = 150pF, Li = 10uH measuring range: 0 ~ 30 m Measuring cycle: 0.5 seconds Resolution: 0.02mm Temperature drift: ± 0.5mm (-40 ℃ ~ 85 ℃) Working pressure: 6MPa Max linearity deviation: ± (1 + 0.05% FS) mm solid-state relays (UCG-3011- R): Configuration: four SPST (NO) solid state relay load voltage: 220V AC / 300V DC (non-explosion-proof) 30V DC / AC (explosion-proof) Load Current: 100mA (-40 ℃ ~ 40 ℃) 50mA (-40 ℃ ~ 85 ℃) alarm mode: "On, Off Alarm" optional five kinds of alarm mode independently selectable delay: 1 to 60 seconds, can be independently programmed medium temperature: -150 ℃ ~ 150 ℃ ambient temperature: -40 ℃ ~ 85 ℃ (ExiaIICT1-T5) -40 ℃ ~ 70 ℃ (ExiaIICT6) Storage temperature: -55 ℃ ~ 100 ℃ protocol: HART Protection: IP65 EMC: CE certification related equipment: UCG-3000S HART Typical applications various sources of water pressure, water softener, water treatment systems, various high pressure room temperature water level monitoring and control system. Light oil, oil level monitoring and control. Polypropylene, polystyrene, nylon and PVC pellets position monitoring and control. Dry pulverized coal, coal ash, fossil powder and cement powder, powder position monitoring and control. Oil-water interface level measurement and control.