High quality Autonics photoelectric switch BEN500-DFRBEN500-DDT sensor warranty ..

Brand: Autonics Model: BEN500-DFR photoelectric switch supply voltage 24-240V AC, 24-249V DC (V) (V) output impedance load 3A uses object detection Ambient temperature -20 ~ + 65 (℃) ( ℃), product certification CE Our customers can request custom various types of products (size, power supply, cable length, etc.) Company honor "; based on quality, market-oriented"; philosophy to quality products, reasonable prices, good reputation for commitment, inviting domestic and foreign customers sincere cooperation, mutual benefit, work together for a better future. BEN500-DFR photoelectric switch type BEN10M-TFR photoelectric switch BEN5M-MFR photoelectric switch photoelectric switch BEN500 BEN3M-PFR -DFR photoelectric switch BEN300-DFR photoelectric switch BEN700-DFR photoelectric switch detection mode transmission type mirror reflection type polarizer Diffuse reflection type detection distance 10m (* 1) 0.1 ~ 5m (* 1) 0.1 ~ 3m (* 2) 500m detect objects φ16mm φ60mm more opaque than transparent body opaque, translucent, opaque or less the amount of delay -------- 20% detection range of response speed Max.20ms Power 24-240V AC ± 10% 50 / . 60Hz 24-249V DC ± 10% (the amplitude of P-P: Max.10%) Current consumption Max.3VA infrared light emitting diode (modulation) Red LED (adjusted 660nm) infrared light emitting diode (modulation) Sensitivity adjustment --- Adjustable by VR operation mode selector switch Light NO / Dark ON mode control output relay contact capacity: 30VDC 3A impedance load, 250VAC 3A impedance load contacts Composition: 1C life mechanical: Min.50,000,000, Electrical: Min.100,000 light-receiving element Built-in light receiving IC indicator action indicator: Orange, steady light: green (transmission power indicator on the transmitter type of orange) cable to connect the wiring insulation resistance Min.20MΩ (at500VDC) ± 1000V interference by the Simulation of the interfering wave interference (pulse width: 1μS) Pressure 1000VAC50 / 60Hz 1 分钟 1.5mm shock, anti-vibration amplitude frequency 10 ~ 55Hz X, Y, Z two hours in each direction malfunctions (period one minute) 1.5mm amplitude frequency 10 ~ 55Hz X, Y, Z each direction ten minutes Shock Shock 500m / S2 (50G) X, Y, Z directions 3 times each malfunction 100m / S2 (10G) X, Y, Z directions for three times the ambient brightness Sunlight: Max.11,000 shi x fluorescent: Max.3,000 shi x Ambient temperature -20 ~ + 65 ℃ (No freezing state), Storage: -25 ~ + 70 ℃ Humidity 35 ~ 85% RH, Storage: 35 to 85 % RH Material Enclosure: ABS, Lens: Acrylic (Reflector: PC) protection class IP65 (IEC standard) wiring φ60.mm, 5P, line length: 2m ---- annex individual mirror (MS-2) - The main technical parameters --- common fixing brackets, bolts / screws weight of about 354g to about 208g to about 195g BEN500-DFR photoelectric switch: Supply voltage 24-240V AC, 24-249V DC (V) (V) output impedance 3A Load uses object detection Ambient temperature -20 ~ + 65 (℃) (℃), product certification CE photoelectric switch works: photoelectric switch (photoelectric sensor) is a photoelectric proximity switch is short, it is the use of a light beam is detected or blocked reflection by the synchronization loop gating circuit to detect the presence or absence of an object. Objects are not limited to metal, all objects can reflect light can be detected. Photoelectric switch the input current at the transmitter into an optical signal injection, the receiver and then based on the received light intensity or the presence or absence of the target object detection. Photoelectric switches classification: ① diffuse photoelectric switch: it is a set of transmitter and receiver in one of the sensors, when an object is detected through, the object will be a sufficient amount of light emitted by the photoelectric switch transmitter to the receiver reflector , then switch photoelectric switch generates a signal. When the surface of the object to be detected light or high reflectivity, the diffuse reflection type photoelectric switch is the preferred mode of detection. ② mirror reflective photoelectric switch: it also sets a transmitter and receiver in one, photoelectric switch transmitter emits light through the mirror reflected back to the receiver, when the object to be detected through and completely blocks light, photoelectric switch is produced detection switching signal. ③ beam photoelectric switch: it contains structurally separated from each other and the optical axis of the relative placement of the transmitter and the receiver, the light emitted by the transmitter directly into the receiver, when the detected object passes between the transmitter and the receiver, and When blocking the light, photoelectric switch generates a switching signal. When the detected object is opaque beam photoelectric switch is the most reliable detection device. ④ slotted optical switch: it is usually a standard U-shaped structure, the transmitter and the receiver are located on both sides of the U-shaped groove and form an optical axis, when the object to be detected through the U-shaped groove and block the optical axis photoelectric switch generates a switch signal. Slotted optical switch is suitable for detection of fast-moving objects, and it can distinguish between transparent and translucent objects, safety and reliability. ⑤ fiber optic photoelectric switch: It uses plastic or glass fiber optic sensors to guide the light, can be detected object distance detection. Usually divided-beam fiber optic sensors and diffuse reflection. BEN500-DFR photoelectric switch environment: Do not water, rainfall, and outdoor use. Action to support the reliability and long life, should be avoided at a predetermined temperature and outdoor conditions. Avoid using strong chemicals, especially salty, sour environment.