Three anti-epoxy paint, low odor three anti-paint, transparent three paint price

Three anti-epoxy paint, low odor three anti-paint, three anti-paint transparent price Introduction Osborne 92 is a dual epoxy protective coating for the protection of working in the harsh environment of the printed circuit board design. It has excellent resistance to high temperature performance, weather resistance, electrical insulation properties and excellent performance of three anti: moisture, salt spray, mildew performance. Full compliance with EU ROHS directive. Features 1, environmentally friendly formula, curing speed, easy operation, suitable for spraying, brushing, dipping a variety of processes. 2, the vast majority have good adhesion, no corrosion. 3, has excellent resistance to high temperature performance, weather resistance, electrical insulation properties and excellent moisture, mold, anti-fog, anti-corrosion, electrical insulation, anti-leakage, solvent resistance. 4, circuit boards, electronic parts, etc. lasting protection, long life, can solder directly on the protective coating. Three anti-epoxy paint, low odor three anti-paint, wide transparent price Typical uses three anti-paint applied to a variety of electronic components, has assembled circuit board, can adequately protect the cable network board in a variety of chemicals, corrosion, salt spray , humid, dusty high pollution, vibration and high temperature and other harsh environments without affecting its working and signal. Use of technology 1, cleaning: Before coating the surface of the object to be coated must first be dust, moisture (moisture), remove the oil, and kept dry. 2, cover: if some connectors, sockets, switches, and other areas not allowed flapper coating material. Osborne recommends the use of solder 120 can be torn plastic cover. 3, the ratio: the ratio of the amount taken by, and the weighing accuracy, please remember that the ratio is the weight rather than volume, A, B need stir mixed evenly, in order to avoid incomplete cure or no cure for 5 minutes , you can use until the bubbles disappear. 4. Dilution: Osborne Osborne 92 108 available three anti-paint thinner diluted by adding a large amount of diluent, low viscosity of the coating, the thickness of the coating on thin; on the contrary, the high viscosity of the coating, the coating thickness on thick. According to process requirements appropriate to add. Stir for 5 minutes, then use until the bubbles disappear. 5. Construction: to use brushing, spraying, dipping methods such as construction. Coating to not flow diagram, missed coating is limited. A film thickness is generally between 0.1 ~ 0.3mm is appropriate, if you want to get a thicker coating, preferably by applying a thin coating layers to obtain, and requires to be in the first layer to dry completely before Allow apply a second coat. Three anti-epoxy paint, low odor three anti-paint, three anti-paint transparent price (1) Brush: brush area should be large than the area occupied by the device, in order to ensure full coverage of the device and the pad; the board as much as possible when brushing flat put, there should Dettol after brushing, brushing should be smooth, you can not have bare parts, brushing back flat on the stand. (2) Spray: adjusted the gun and pressure, the paint diluted into the watering can, spray gun nozzle requires stable, in order to ensure the well through the paint from the bottom components, spray jet should be smooth all angles. (3) dipping: paint diluted dip into the bucket, circuit board assemblies should be immersed in paint vertical worse, the connectors do not immersed, unless carefully covered, circuit boards or components immersion speed is not too fast to avoid bubbles. 5, the cure: after construction flat on the stand, room temperature or heated to 60 ℃ can be cured. Curing process, please keep the environment clean and avoid impurities or dust fall into the uncured coating surface. 6, repair: repair have been coated device, simply solder coating can be in direct contact with a soldering iron to remove the components. Then install the new components, and then clean the area with a brush or solvents; solvents can also be cleaned; dried and re-coated with paint well. Three anti-epoxy paint, low odor three anti-paint, transparent three paint price