Reiter environmental resistant emulsion metalworking lubricants, non-allergic cleaning cooling effect

Reiter resistant metal cutting fluid (GR-P1) Use a product Reiter resistant metalworking emulsion with excellent lubricity, corrosion resistance, cooling, cleaning, sterilization, can meet business grinders, lathes, saws and other equipment and technical requirements for vehicles, drilling, expansion, grinding, holes and other processing. In addition, anti-Reiter metalworking fluids also have biodegradable, green, no adverse stimulus on the operation of the workers, does not pollute the operating environment. Second, the special nature of the product in all biological materials soy-based material, without any chemical petroleum feedstocks, the human body without irritation, allergies, heavy metal residues and other hazards. Product is patented technology Henan University of production, the only. The technology is dozens of Henan University Professor of School of foodstuff, Materials Science, Mechanical and Electrical Engineering, Institute of Chemical Technology, abrasive Institute and the Central Laboratory department, etc. After nearly five years of joint development acquired. Products through the practical application of the second machine tool plant in Zhengzhou, Zhengzhou bearing factory, Zheng drilling Group and many other well-known enterprises, have achieved very good results, product performance can be comparable with foreign products, and cost far less than imports products. At the same time, to avoid contamination of the environment, in line with the latest environmental policy of the country. This product has a special smell of milk, it is because of the inherent reason raw materials, the product does not add any flavor additives cover gas. Third, the good performance characteristics (1) cooling performance. Greatly cutting away heat and sufficiently cooled cutting tool cutting edge, to keep it the hardness, strength and sharp cutting ability, thus improving work efficiency. Superior (2) lubrication. In the cutting area to form the lubricant film, cutting fluids largest non-card bite load reaches 640N more than coincidence. Which can greatly reduce the cutting forces and reduce the consumption of cutting tools and grinding wheels. (3) that, in use, lubricating cutting fluid can penetrate the surface of the workpiece cut very fine cracks, embrittlement of the surface of the metal lattice, making cutting easier. (4) has good mobility and good cleaning properties. (5) has excellent chemical and thermal stability, and rust resistance. It does not decompose at high temperature, high pressure and air contacts, not bad, not corrode metal surfaces. No rust within two weeks at room temperature workpiece. (6) has excellent stability. When storage and use, no precipitation precipitation is not hierarchical, non-perishable, no interfere with workers' health gases. Meanwhile, the product does not contain harmful sodium nitrite and mineral oil, the working environment is clean, odorless, can be clearly observed when machining the workpiece surface. (7) The new water-based cutting fluid waste very little work, biodegradable, easy to handle, greatly reducing the environmental pollution Fourth, the physical and chemical indicators: quality indicators have reached the GB / T 6144-85 requirements. Project Quality Indicators Appearance creamy liquid storage stability even qualified translucent transparency defoaming pH 8.0 (mL / 10min) ≤1 corrosive gray cast iron A grade A-grade aluminum A-grade copper rust resistance Monolithic A level laminate A grade five, using the method 1. 3-15% water or soft water diluted mix and use, adding more of the product, the more features. 2. When the amount of cutting fluid loss total reaches cutting fluid 1 / 2-1 / 3, to timely additional liquid or an appropriate concentration of fresh working fluid. 3. liquid method and manual can overflow, high pressure, spraying and other automatic method for liquid supply. 4. The use of fresh water quality should be formulated in the working fluid. VI Notes 1. suggested the use of fresh water quality, in strict accordance with the proportion of preparation of the working fluid. When replenishing the working fluid, should be supplemented with a higher concentration, prevent lubrication, corrosion performance. 2. Keep clean cutting fluid mixed with metal chips prohibition, oil, and other debris; prohibit washing hands with the working fluid, wash rag. 3. After the shutdown, the machine should be cutting fluid clean with a dry cloth, preferably oiled rust. The workpiece long term storage, for poor materials, anti-rust treatment is recommended. Seven Packing 18L, 20L plastic drum, 200kg drums. Eight safety test: toxicity: the No. 1, No. 2 Two containers 10L water was added, to which were added to 0.5g and 0.5g of the ordinary cutting fluid cutting fluid (ie give two cutting fluid concentration of 50mg / L). Last five small fry to put each container separately. At least twice a day record number of dead fish in each container and dissolved oxygen concentration, and promptly remove dead fish. 48h later, the 1st vessel are down a little fish, and close to death, the 2nd container, survived four. BOD: Using the measured dilution BOD, the water samples were appropriately diluted so that where there is enough oxygen for microbiological and biochemical oxygen requirement, this water is divided into two. A measured amount of dissolved oxygen before the culture; the other one into the determination of dissolved oxygen at 20 ℃ incubator culture 5d, the difference between the two is the BOD. (Dissolved oxygen consumed more, BOD the greater the poorer water quality). Test results shown below. Environmental performance evaluation results Evaluation Index of new ordinary cutting fluid cutting fluid skin feel to the skin, eyes and nasal irritation no irritation toxicity contain toxic ingredients, non-toxic biological oxygen demand (mg / l) qualified chemical oxygen demand exceeded (mg / l ) exceeded qualified