Supply Haihong HEMPEL coatings, architectural coatings, marine coatings, floor coatings

Overview: HEMPEL 15500 is a two component epoxy paint amine adduct cured phenolic epoxy coating with multiple resistance to chemicals ("Cargo Protection Guide" in the column and the) excellent performance. Uses: used tanks lined paint. Temperature: dried (no temperature difference) (maximum) 160 ℃ 50 ℃ temperature in seawater in wet and other liquids, refer to the appropriate "Cargo Protection Guide." Certification: The "Lloyd's Register" and Russian Maritime Register of Shipping approved as anti-corrosion coatings. Compliance with US FDA on food transportation provisions of Federal Regulations section 175.300, apply to more than 2006 m 3 volume of food compartment. Physical parameters: Color / Color: white / 11630- reddish / 50900 Paint: Flat Volume solids: 68 ± 1% Theoretical coverage: 6.8 m 2 / liter (100 microns dry basis) Flash Point: 26 gravity ℃: 1.7 kg / liter Surface dry: 2-3 hours (20 ℃) ??Touch dry: 4-6 hours (20 ℃) ??completely cured: 10 days (20 ℃) ??(see Note) VOC 325 g / liter content (VOC): storage: 1 year (25 ℃) shelf life depending on storage conditions, the need for mechanical stirring before use. Construction Description: Mixing ratio: Base 15509: Curing Agent 97580 = 8.9: 1.1 (volume ratio) = 93.8: 6.2 (weight ratio) construction method: airless spray Brush (repairing) Thinner: 0,845,008,450 (the largest volume ) (see note) (see note) mixing time: 3 hours (20 ℃). Pre-reaction time: 15 minutes (see note) orifices: 0.46-0.58 mm discharge pressure: 20.0 MPa (Airless spray data are indicative and may be adjusted practically.) Cleaning of tools: HEMPEL tool cleaner 99610 Film Thickness: Dry: 100 microns (see Note) Wet film: 150 microns; recoat: minimum: 36/24 hours (20 ℃) ??Maximum: 21 days (20 ℃) ??(see Note) Safety: Be careful using this product, when used before and use, please pay attention to packaging and all safety labels on cans, should refer to "HEMPEL Material Safety Data Sheets" and abide by the state or local government safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take the necessary precautions against possible risks of fire, explosion and environmental protection. Construction of this product only in well ventilated areas. In confined spaces or poorly ventilated office construction, must provide strong ventilation. Finish: In order to get in line with the majority of chemical coating on the best performance of "Cargo Protection Guide", the substrate surface should be blasted to near white level Sa2.5-Sa3 level, surface roughness standards equivalent Rugotest The NO.3, BN10, Keane-Tator Comparator 3.0 (angular sand / steel shot) or ISO Comparator Medium roughness (angle sand). Referring to the corresponding "Application Guidelines." Construction conditions: Use only at temperatures above 10 ℃ construction and curing can proceed. The film is completely cured before the steel temperature must not be below this temperature. The temperature of the paint itself may not be lower than 15 ℃. Preferably between 17-23 ℃, the best construction. The maximum relative humidity of 80%, preferably between 40% -60%. Surface must be clean and dry, the temperature is higher than to avoid condensation. In confined spaces provide adequate ventilation during application and drying must. Please refer to the corresponding "Application Guidelines." Preceding coat: None Add Tu paint: None Note: When part of the certificate issuing, the product model for 1550. Film thickness: The minimum total dry film thickness of the supporting system of 300 microns. Film thickness may increase depending on purpose and area. This will alter spreading rate and drying time. For more information on the film thickness, please refer to the product's "construction guidance." Color: There can be nuances and 11630 colors. Recoat: If more than the maximum recoat interval should primer surface roughening. Mixed: After thoroughly mixed base and hardener need pre-reacted 15 minutes (20 ℃) ??and then construction. Pre-reaction time at other temperatures, see Application Guidelines. Dilution: minimize the use of diluent may not dilute the components separately, only for mixing paint dilution. Cure: cured by heat resistant to many chemicals. See Application Guidelines and "Cargo Protection Guide."