Our large supply through intelligent control unit HYD-5600

Product Overview This product uses the single-chip microprocessor control, not only innovative and unique design, while the misuse voice prompts, judging switch the car is in the test position or working position, with RS485 remote communication. Industrial-grade electronic components, high reliability, long life, anti-jamming capabilities, product design life of 30-year warranty for 10 years. This product is used 3-35KV outdoor switchgear cabinet and for the home, the handcart cabinet, fixed cabinet, ring main units and sulfur hexafluoride gas cabinet. Technical Specifications 1, the working voltage: / 220 V ± 10% 50 ACDC Hz 2, heating and dehumidification Power supply: AC 220V ± 10% 50 Hz 3, power consumption: ≤10W 4, temperature range: 0 ~ 99 ℃, accuracy ± 1 Kai condensation control point 93% RH, accuracy of ± 5% RH 5, the electric strength; ℃: greater than between the shell and the terminal AC 2000 V 6, the insulation performance: greater than 100 MΩ 7 between the shell and terminal, anti-electromagnetic interference performance : in line with the standard IEC 60255-22 8, the working environment: Temperature -20 ~ 70 ℃ Relative humidity ≤95% RH 9, hole size: 220mm × 165 mm Dimensions: 230 mm × 178 mm × 69 mm Function 1, simulated instructions: Circuit breaker status indicator (passive contact input) circuit breaker position indicator (passive contact input) Closing, the closing contact is closed, the red light working position analog bar contacts are closed, the red vertical analog bar light sub-gate, the sub-gate contact is closed, when the green light experiment simulated the location bar contacts are closed, the level of analog bar green light Earth switch position indicator (passive contact input) Spring energy storage instructions (passive contact point input) contact closure, analog bar red light, said ground contact closure switch on the red lights that are energy storage Contact off, the green analog bar light, disconnect the ground contact is open, the red light is off, indicates that no energy storage Note: The loss of power in the state all of the flares are off, the above contact signal from the circuit breaker auxiliary contacts. 2, high pressure part of live instruction LED striking voltage (KV): bus voltage × 0.15 ~ 0.65, lockout Kai control voltage (KV): bus voltage × 0.65 3, temperature and humidity control part Sensor approach: two condensation + two channel temperature Logic: When the ambient temperature is less than 5 degrees or humidity higher than 85% RH, the device starts heating, when the ambient temperature is above 10 degrees, the heater automatically stop heating; when the humidity is lower than or equal to 75RH%, heater stop heating. When the ambient temperature is greater than 40 degrees, the system is forced to stop heating, heat exhaust lights, fans began to work, when the temperature is below 35 degrees fan stops working. Manual heating switch: auto or manual switch can be in two states, usually in the automatic mode, when temperature and humidity control logic above, when you press the switch, then manually force in a heated state 4, smart anti-error prompts (choice. equipped) When the circuit breaker is in the test position between the working position, when the circuit breaker is in closing state, a "sub-circuit breakers," the voice prompts until the circuit breaker after the operation ended, in order to prevent the operator When the circuit breaker is closed, the error Used to promote the work position. When the circuit breaker is in the working position or test position, the circuit breaker is closing another state, if the error is forced to switch on grounding switch, the "please point grounding switch," the voice prompts, the operator until after the opening operation is stopped to This prevent the operator closing earthing switch. When these two conditions occur simultaneously, the "sub-circuit breakers, please point grounding switch," the voice prompts. 5, the communication function (optional) The device has RS485 communication interface, can be transmitted in real time location status handcart, breaker position status, the spring energy storage state, grounding switch status, low-temperature heating, is overheating alarm and a series of parameters. 6, the other auxiliary functions The device panel, the matching requirement specified by the user points / closing million transfer switches, remote / local million transfer switches, storage and cabinet lighting switches, the user can be related directly onto the unit operation. 2. Schemes (Pictured standard used concrete follow-kind prevail.) 1. Installation: panel mounting (thickness) of the unit: 70 mm installation hole size 230 120 220 3. Dimensions of the sensor 45 37 2-φ4 with screws in the appropriate cabinet position can bring their own guides 35 mm installation and wiring 21 Service 1, the company sold products commitment: one year warranty and lifetime maintenance; 2, starting from the date of sale of products, In the one-year warranty period, belong to non-human causes damage to the product, our repair replacement; otherwise belong to paid services; 3, more than the warranty period, is a paid service.