Cinema with PVC material level lighting stepping lamp manufacturers

Qingdao Wing Cheong Shing insulation materials Co., Ltd. to provide you with: supply aluminum profiles LED step lights, theater lights stairs, supply PVC profiles LED step lights, theater lights staircase structure and specifications: Step-grade light aluminum body 4550 * 92 * 44mm in steps high and low voltage strip lights 3610 * 70 * 13mm in steps of light digital Grades 90 * 80 * 50mm in steps of adjustable lamp power to do product described in terms of the use of power: a body made of high quality 6063 aluminum profiles as raw material by the extruder molding, profiles thickness of 3mm, product environmental protection, fire-retardant, wear-resistant, non-slip, noise reduction, and the product durable, long service life, the surface can be plain oxidation, electrophoresis, electrostatic spray, can also be customized according to customer requirements in different colors, color attached a strong, high abrasion resistance, product size is 92 * 44mm body embedded in the front rubber non-slip, non-slip, noise, wear, environmental protection, B1 retardant. The light emitted from the light diffusion PC tube made of high quality materials, wall design diffusion stripes, do the punch line of the outer wall of a card, so that the light distribution on the wall, look and feel soft, colors. Under 方光源 using LED spot light, adjustable brightness, the substrate is made of aluminum, heat and strong, the color blue, green, red, etc., can be customized according to customer requirements, lamp beads spacing 10cm, working temperature -20 ℃ --150 ℃ lamp life of up to 100,000 hours, soft lighting, a 5V power supply, optional power adjustable, low power consumption, energy saving. Configuring two corner sections at both ends plug, one with digital Arranging, both closely, perfect match, making a nice step, etc., the product structure: Product body made of three parts 1, profiles, light bar, seal the first two, high and low bar (go trough) 3, adjustable power Second, the installation steps: 1, the amount of the step size, reasonably calculate the size, cutting profiles: profiles have been cut as well, to cut into the corresponding profile the length of the stairs. 2, connecting light bar: Place one strip with a thread of light and non-light bar with thread with docking connector (inserted in place as far as possible, so as not to loose contact failure), the length of the connection with the corresponding profile as the positive and negative agreement; On another card small cards, the number of small cards to one meter light strip card 5 prevail. 3, wearing a light bar: the lights take a good penetration profiles A, light obliquely downward direction, the plane light is weak and does not glare, fa?ade lighting, able to illuminate the stairs to the next level, standing below the steps up distance Some glare, within five meters of excellent results; the B, light obliquely direction, flat light, strong, slightly dazzling look straight down, standing up or far below the level not dazzling; 4, then the power: the power supply (transformer ) AC end position connected to the 220V LN polarity (exchange), ground position indicator ground; the positive OUT (output) (DC 12V) + V pole position lights column connected to the main line of the step, -V pole connected to the main line of the negative column, so that the main line is energized, determine current is 12V. 5, wiring: the thread pick a good light on the strip were received on the positive and negative main line, wrapped around the insulating tape, lights; if not light, there is power on the main line to be checked, whether it is 12V, positive and negative It is reversed. 6, with a number of the lamp, the number of circuit board into the slot, the circuit board and the card column level, such as circuit boards for too long, to be cut off long portion; thread through from the position of the large hole in the fifth Article synchronous to thread together the combined received on the main line, pay attention to the positive and negative agreement. 7, step drill: put away will put light profiles corresponding location, close to the front steps, the carpet in front of the location of the pressure profile with an impact drill holes of 6mm, smashing into the plug up; 8, the fixed profiles: diameter Shen head screws 4.8mm will be fixed profiles, the facade of the position can be suitably reinforced with up bolt or pin 9, fixed head, the head, fixed; cover with black lid, with a number of lights: Cleaning head inside the dust, put the corresponding plate, changing for the better transparent cover. 10, installed, check for loose, damaged, and repair.