Taian automotive paint room affordable option Shandong Jinding custom factory direct

Painting Equipment Co. Jinding paint room temperature characteristic: the traditional high temperature baking is artificial semi-mechanized, first work efficiency is not high, artificial paint workflow complexity, staff skills requirements, consumption, paint quality is difficult to guarantee frequent accidents difficult environmental standards, easily causing bodily harm, to enterprises and institutions to bring high-cost, high consumption, but also affect the production schedule enterprises. However, with the progress and development of science and technology, modern high-temperature paint rooms also keep pace with the times, and the emergence of Jinding paint room temperature, will lead the huge development of the automotive paint industry, it is a major advance in the automotive industry. Jinding paint room temperature with the following advantages: First, the pre-treatment fast, the effect of pride: TIS high temperature baking room is a set of large equipment. Before using the car will go through the pre-treatment. This not only eliminates the disadvantages of manual processing, improve work efficiency and improve the quality of the paint repair paint job. This is not only because the paint room allows the operator to set the paint according to a uniform temperature and rapid drying, and Booth can be isolated from the outside world pollution caused by dust and other pollutants in the paint, so that eliminates the need for subsequent polishing finish treatment the work. Second, the Jinding paint room temperature good working environment. Paint the room in order to keep the air clean, various types of high-temperature paint rooms are equipped with filtration devices, such as cotton filters, to filter into the paint room of dust in the air, and high-temperature paint room ventilation system would paint the room there is sufficient ventilation speed, thus ensuring high-temperature paint the room air clean. In many cases, contaminated body paint is caused by human factors, such as painting the vehicle is not to be thoroughly cleaned enters the paint room, or painting dedicated staff did not wear protective clothing, or paint the room dirty and so on. High efficiency, quality is guaranteed. Compared to artificial paint, paint, paint room temperature Jinding mechanized "one-stop" service, efficiency several times higher, or even several times. And, when painting the outside air filter after primary filter by the fan to the roof, and then after the top of the second filtration and purification filter into the room. Room air with full drop style to 0.2-0.3m / s speed of downward mobility, so after painting the mist particles can not stay in the air, and direct air is discharged outside the room through the bottom out. Such continuous cycle conversion, so when painting the room air cleanliness more than 98%, and is fed with a certain air pressure, it can be formed around the car a constant air flow to remove excess paint to maximize assurance ! Jinding Painting Equipment Co. automotive paint room use Maintenance of common sense: Choose a qualified Booth is important, but over time the paint room equipment in use, the difference between a lot of paint spray booth master reflect quality, relatively dust room more poor construction effect, even some time not as the effect ????? outdoors. I want to say is: In fact, if we can paint the proper use and maintenance, these problems are completely avoidable. ? 1, coating must be checked before making spray pressure is normal, while ensuring that the filtration system clean; 2, check the air compressor and the oil-water separator dust, so painting the hose to keep clean; 3, spray gun, spray hose and paint cans to be stored in a clean place; 4, except with the hair * and sticky dust cloth, other processes before spraying should be done in all the outer paint room; 5, in the paint spraying and baking room only processes, and paint the door can only be opened when the vehicle is out, it must start spraying air circulation system to generate increased pressure to open the door, to ensure that dust can not enter the house outside of the room; 6, must wear the designated painting clothes and wear safety equipment to enter the paint room to operate; 7, during the baking operation, you must paint the room to come up with flammable liquids outside the room; 8, non-essential personnel shall enter the paint room. In daily maintenance, to keep the paint room best results, should be regularly cleaned and inspected by doing the following: 1, clean room every day pencil, glass and floor base, in order to avoid the accumulation of dust and paint dust; 2, each week cleaning the inlet air filter, exhaust air filter to check whether there is product plug, such as when the room no reason to increase the pressure, exhaust dust filters must be replaced; 3, should be replaced after every 150h floor dust filter fiber cotton; 4 , should be replaced after every 300h inlet dust filter; 5, monthly cleaning floor drip tray and clean diesel fuel filter device on the burner; 6, should be checked each quarter inlet and exhaust motor drive belt slack ; 7, should be cleaned every six months throughout the paint room and floor look, check the circulating air valve, inlet and exhaust fan bearings, check the burner exhaust passage, clean sediment inside the tank, clean paint room Aqueous protective film and re spraying; 8, each year should clean the entire energy converter, includes a combustion chamber and the exhaust passage, every year or after every 1200h paint the roof should be replaced cotton. If you usually take into account the above points and the rational use and maintenance, paint rooms in the construction process will become easier and tidy, while the quality and quantity to complete the task, some showing a perfect coating results. ?? Because many domestic and foreign brands Model: Different models can be divided into: general purpose, medium and far infrared, but each with a different standard. ?