Shelf cement glue manufacturer wholesale cement cracks crack repair

Volatile cement products member minor cracks (chicken lines) for the sticky glue cement products member minor cracks (chicken lines) for the sticky glue of high quality resin, curing agent carefully made, 100% solids, solvent, etc. of harmful substances. Stir at room temperature, mixed A / B immediately after use, without adding any additional ingredients. The product is easy to use, non-toxic, non-irritating odor, mixed cured adhesion, high hardness, excellent weather resistance, water resistance, oil resistance and other properties. First, use: cement products member minor cracks (chicken lines) for the sticky glue patch designed specifically for the chicken grain surface cracks in the cement produced using the process after brushing brushing the surface of the cement product, mixing glue will quickly penetrate fine cracks, to fill the fine lines of purpose, and as a protective layer to protect the cement, to improve weather resistance. The product can be bonding wood, metal, plastic, etc., hard after curing, excellent mechanical properties. Second, product characteristics: 1, cement products member minor cracks (chicken lines) for the sticky glue in liquid form, easy to carry out concrete repair small cracks. 2, building and structural damage, the infusion of plastic reinforced, it could effectively restore its integrity, and the appearance is not damaged. 3, non-volatile solvent, basically does not shrink when cured. 4, with good toughness and impact resistance. 5, operational for a long time, after curing adhesive strength. 6, has good resistance to water, oil, acid and alkali capacity. Third, the product scope of the project physical performance index value detected value test compressive strength MPa 90-105 60 GB / T50081-2002 flexural strength MPa 25-35 30 GB / T50081-2002 modulus of elasticity MPa 17-20 18 GB / T50081-2002 thermal expansion coefficient of <40 × 10-6mm / mm / ° C GBJ119-88 linear shrinkage ----- HG / T2625-94 ratio: A: B = 2: 1 Construction: 1, clean up : detailed examination, analysis of leakage, grouting holes to determine the location and spacing. Needs of the construction area clean, chiseled concrete surface precipitates, ensure that the surface is clean. 2, drilling: drilling using hammer and other tools to crack along the sides of the borehole, the drill diameter of 14mm, drilling angle should be ≦ 45 °, drilling depth ≦ 2/3 thickness of the structure, drilling must pass through the cracks . But not penetrated the structure (excluding grouting wall) drilling and fracture spacing ≦ 1/2 thickness of the structure. Drilling spacing 20cm ~ 60cm. 3, buried mouth: the drilled hole installation filling the mouth (also known as sealing needles), and hex wrench with a dedicated, so that no gap between the grout and drilling around the mouth, watertight. 4, wash joints: use a pressure washer to pressure 3Mpa injection nozzle into the grout clean water, the water point to observe the situation, in the dust and clean the seam. 5. Sealing: Cracks surface water seepage appears be closed when the wash is treated with quick-drying cement seam, the aim is not to run when filling chemical pulp slurry. 6. Filling: Using high-pressure grouting machine to the filling hole perfusion chemical grouting material. Facade filling up order by the following; plane can start from one end, single-hole one by one continuously. After the start of the plasma adjacent holes, keeping the pressure for 3 to 5 minutes, you can stop this hole grouting, grout Injection in adjacent holes. 7, split mouth: grouting is completed, confirm no leakage can be removed or knocked exposed filling the mouth. Clean up spills out of the cured grout. 8, sealing: repair grouting mouth with quick-drying cement, sealing process. VI, packaging and storing packaging: 20KG / drum, ventilation cool storage, shelf life of six months. The product transport in accordance with general chemical transport. Contact: Li Gong Mobile: 13930123708 QQ: 87954084 Fixed: 0311-69002772