Wholesale condensers Han Zun

Condenser works for some applications, the gas must pass through a long tube (usually set into a solenoid), so that heat loss to the surrounding air, the thermally conductive metal such as copper is used to transport vapor. To improve the efficiency of the condenser fins are often attached to the pipe in order to accelerate heat dissipation. Fin is a good heat conductor plate made of metal. Usually this type of condenser fan is also used to force air through the fins and the tropics away. The role of general refrigerator compressor refrigeration principle is to compress low pressure steam into high pressure steam, so that the volume of steam is reduced pressure. The compressor suction from the lower pressure evaporator steam out of the working fluid, so that the pressure rise into the condenser, condensed in the condenser to a higher pressure fluid, after throttling the throttle valve, the pressure becomes relatively low liquid into the evaporator, absorbing heat in the evaporator is evaporated into low pressure steam, thereby completing the refrigeration cycle. Advantages First, all stainless steel manufacturing material: Heat Exchanger made of stainless steel 316L, corrosion resistance, service life of up to 10 years. Features: Highly antirust also acid-proof; good solderability: weld tenacity; plasticity Haonai pull manufacturing materials, resistant to carve; oxidation with a chromium oxide protective layer; second, best-designed 90-degree connector resistance noise reduction, reduce drop; sewage and convenient, reduce fouling; easy to install, reducing investment. 1, the heat transfer coefficient, high heat transfer efficiency, heat capacity per unit area is the traditional shell and tube heat exchanger 3-7 times, multi-threaded pipe coiled helix; 2, high temperature, high pressure, safe and reliable, whole stainless steel welded structure, uniform coefficient of expansion; the highest temperature 400 ℃, pressure 1.6MPa, the steam system, no separate increase pressure reducer, saving system cost. 3, the elastic tube bundle automatically eliminate stress damage. 4, small size, light weight, easy to install, is the traditional shell and tube heat exchanger 1/5, no special foundation, and the pipeline is connected only; saving installation and infrastructure costs. 5, 90-degree connection optimally designed for fluid cushion, reduce noise and heat noise is not more than 60 db; 6, significant energy saving, less steam energy, heat fuller, lower operating costs. Advanced Flexible spiral heat exchange bundle forced turbulence, heat transfer and adequate; long heat exchange tubes (3-4 times for the housing height); material to stay a long time, heat sufficient. Product design flow rate of up to 5.5m / s (the traditional design of 1-1.5m / s), medium easy attachment of suspended solids and impurities, is also a key factor in reducing fouling. 7, post low maintenance costs, long life and easy to clean, low maintenance costs. Small; small footprint; maintenance cleaning when labor-saving convenience and low cost of cleaning. The heat exchanger is one of the world's most advanced tubular heat exchanger products. Original U-shaped thread, the thread reasonable gap, reverse wound bundle structure, the steam inlet tube, water into the shell. Unique two-phase mode of operation, greatly changed the fluid flow state, good turbulence effect, its integrated heat transfer coefficient up to 14000W / m2. ℃, efficient heat transfer, environmental protection and low noise, compact structure, small footprint, volume only one-tenth of the conventional heat exchanger. . High temperature 400 ℃ high pressure 1.6Mpa; heat exchanger with the central axis of the angle between the ends of the two flanges using 90 ℃ connection allowing participation of all heat exchanger, automatic erosion, reduce noise, less heat loss, heat recovery 96 % or more, and it can be a conventional shell and tube heat exchanger 3-7 times. With conventional heat transfer equipment can save energy compared to more than 15%. Application of industries and fields screw thread tube heat exchanger uses mainly condensate, cooling and heating medium. Because of its performance was significantly better than conventional heat exchangers, therefore, it has gradually replaced the traditional heat exchangers in the chemical, thermal power, paper, pharmaceutical, textile, food, shipbuilding, machinery, HVAC and other industries to promote the rapid and Applications. Civilian areas:?? HVAC hot water district heating industry:? Industrial heating industrial water, the solvent is condensed back to liquid cooling food machinery:???? Retorts CIP Cleaning System pharmaceutical field: distillation reflux, concentrated extract, solvent recovery, material was dried and fine chemicals:? craft medium is cooled, the solvent condensate recovery medical devices: sterilization machine disinfection me?