Guangdong resin tile glazed tile durable environmentally friendly anti-corrosion anti-corrosion

Product characteristics of the resin of a watt, excellent resistance to load: a good carrying capacity. In the lower temperature region, even if the roof perennial snow, it does not produce surface damage and breakage. After testing, in the case of support from the 660mm, the load 150kg, tile does not produce cracks and damage. Second, sound effect: The experiment proved: When subjected to external noise storm, high winds, synthetic resin tile has a good noise absorption effect. Third, impact resistance, good low temperature performance: a strong outer affordability. The test 1 kg steel ball from 3M high free fall will not crack, impact resistance at low temperatures is also very significant. Fourth, excellent corrosion resistance: long-term resist acid, alkali, salt and other corrosive chemicals. Experimental results show: soak for 24 hours without chemical reaction in salt, alkali and various acids below 60%. Ideally suited for acid rain-prone areas and coastal areas, the effect is particularly significant. Fifth, the insulation performance: thermal conductivity 0.325w / mk, approximately 1/310 clay tile, cement tile 1 / 5,0.5mm thick steel tile 1/200. Therefore, under no circumstances consider adding insulation, thermal insulation properties still achieve the best results. Sixth, self-cleaning properties superior: dense and smooth surface, with the "lotus effect" itself is not easy to absorb dust, once the rain washed clean as new, tile surface dirt will not appear after rain washed mottled color phenomenon. Seven, volume stability: expansion coefficient of the synthetic resin tile was 4.9 * 10mm / mm / ℃, while tile has two-way stretch performance on geometry, even if the temperature changes greatly, tile can also be self-digestion stretching, thus ensuring geometry stable eight excellent waterproof performance: synthetic resin tile chosen dense high weather resistant resin itself does not absorb water, there is no pore water seepage problems, wave height product 45% higher than traditional tile roof seams less so than The traditional nine greatly improved water resistance, excellent insulation properties: synthetic resin tile insulation products, encountered an unexpected discharge will be intact ten, fire resistance: a flame retardant materials XI, quick installation: the effective width of 960mm high paving efficiency; light weight, easy handling; installation accessories complete. Twelve, green: does not contain asbestos and radioactive elements, and recyclable, in full compliance with environmental protection requirements. Installation Instructions resin shoe mounting method _ a copy of a copy of the resin shoe mounting method _ 2 synthetic resin tile installation: Before installing the discharge line should be placed at the scene roof line situation, which helps to achieve smooth vertical and horizontal tile installation to ensure the installation quality and to achieve beautiful results. When installing the main two sloping roof tile main shoe mounting, side crest center CC1 (CC2) or DD1 (DD2) lines coincide, the main tile, the lower should be parallel to the CD, AB line, and from one side (CC1 or DD1 Line) to begin the installation. The first tile installation is most important, make sure the bottom edge of the tile CC1 (CC2) or DD1 (DD2) perpendicular not tilted, straighten after location, in the center of the lower end of the purlins and Watts (peak) at the W Fixed. To prevent unidirectional lap due to tilt and uneven phenomenon, mounted transversely to a main tile on, what order, namely the second tile withhold the first and third tile tile, tile withhold fourth and third fifth tile and each lap a Wabo, rest and so on. The installation process should always check the bottom edge of the vertical tile and construction lines, confirmation and then the fastener installation is complete. A longitudinal section of the installation to shingle length. Two sloping roof should be installed on both sides of the shoe master simultaneously, in order to ensure consistent positive ridge crest of the shoe mounting. Main shoe mounting diameter chosen 6.3mm, length 75mm self-tapping screw; positive ridge tile, depending on the oblique ridge shoe mounting a fixed position, the choice of diameter 6.3mm, length 110-150mm self-tapping screw. Fixed tile first waterproof ring placed in a groove under protection pads and self-tapping screws through the protective pad center hole (arc down), to drill perpendicular to the tile surface, fastened to the elastic nails watts moderate, installed after the flashing. Steel purlins using self-tapping screws or stainless steel spikes, wooden purlins using self-tapping screws. On the need to drill a fixed crest self-tapping screw hole diameter is larger than 2mm, and every crest fixed set of accessories. Ah hipped roof first main tile installation (method with two slopes house). Installed after the main shoe mounting on both sides of a triangle roof from the centerline of CC3, DD3 as a benchmark average installation on both sides, then cut along the diagonal, in order to oblique ridge tile installation. Install timing ridge tile being installed in the house crest crest of the shoe line CD, the installation from the main tile area starting side, the first being the ridge tile lap to avoid overlap with the main tile lap, lap between two positive ridge tile a waveform. Oblique oblique ridge ridge tile installation shoe mounting on a multi-slope roof triangle hypotenuse, the installation should align vertically fixed to the main tile purlins, 30mm overlap between the two oblique ridge tile, ridge tile end of the final installation. Tee Tee ridge tile installation shoe attachment on three sides intersect the apex, is, after completion of the installation of the shoe mounting oblique ridge ridge tile tee, three-way installation lap while under the positive ridge crest tile tile, the other two sides in oblique ridge lap tile top. Install the fascia fascia should be installed with most main tile in the next section, with the main tile end of a double self-tapping screw fixed to the purlins. Such as the main tile eaves purlin distance is too long, when fascias long enough, fixed with bolts alone.