A10 pneumatic diaphragm pneumatic diaphragm Fu Xu Painting

Products pneumatic diaphragm pneumatic diaphragm pneumatic diaphragm Chongqing Fu Xu Painting 8501 A-10 pneumatic diaphragm pneumatic diaphragm pumps are powered by compressed air, proper lubrication can make the operation of the pump is more stable and can extend pump life . 2) to ensure clean air, easy to wear dirty gas valve, install the pneumatic FRL! 3) Switch device must slow start off slow to reduce the impact of the pipeline and separator, before starting to check for loose pipe connection. 4) Please put an exhaust pump connected to a safe place when transporting hazardous liquids, to avoid the risk of damage to the diaphragm. 5) After transporting liquid please easy to dry cleaning, in order to avoid damage to the diaphragm or the next start will not start. 6) long pipeline, the pipeline to be fixed, not with pump tubing to bear the weight and vibration. Performance parameters Chongqing pneumatic diaphragm pneumatic diaphragm pneumatic diaphragm Fu Xu Painting A-10 pneumatic diaphragm pneumatic diaphragm 850 Troubleshooting: a pump in operation, but the flow is too low 1. Check whether the pump Available plaque like, adjust the inlet pressure of compressed air. Reduce operating speed of the pump to adjust the viscosity and concentration of large liquid. 2, check whether the ball valve is stuck. If delivery of the liquid and the valve ball materials do not coincide. The ball will swell. Replace the appropriate ball valve seat material. 3, check the inlet pipe is blocked. Second, pneumatic pneumatic diaphragm pump can not start or slow action 1, check the filter, regulator and lubricator and the air inlet filter is clogged. 2, check whether the valve is stuck impurities, please remove and clean the valve to see if there are scratch marks inside the piston valve. If the piston surface is bright but not pure black, indicating the need to replace worn piston and "O" ring. Injury marks. If the piston surface is bright but not pure black, indicating the need to replace worn piston and "O" ring. Please replace the new 3, check the spindle and "O" ring for scratches, wear and signs of flattening, if damaged, replace it. Third, the liquid from the chamber discharge port leakage 1. Check for diaphragm rupture. 2. Inspect the diaphragm is properly installed and locked. Fourth, the export liquid contains a lot of bubbles off 1. Check for diaphragm rupture. 2. Check the pump and piping for leaks. Use and maintenance 1, powered by compressed air. 2, features pneumatic diaphragm pump is a reciprocating diaphragm deformation caused by the volume change of the solvent pump, it works similar piston pump, since the characteristics of pneumatic diaphragm pump works, so pneumatic diaphragm pumps have the following characteristics: (1) Pump will not overheat: compressed air powered, is an expansion in the exhaust endothermic process, pneumatic pump when the operating temperature is lowered, no harmful gas emissions. (2) does not have a spark: pneumatic diaphragm pumps without electricity for power, ground and then prevent electrostatic spark (3) through a liquid containing particles: type of work and because of the volume of imports for the ball, it is not easily blocked. Note the role of a pneumatic diaphragm pump, since the air-powered, so flow with back pressure (outlet resistance) changes automatically adjusted suitable for high viscosity fluids. The centrifugal pump operating point is the water as a benchmark to set a good, if slightly higher viscosity of the fluid, you need to complete reducer or frequency converter, the cost will be greatly enhanced, for gear pump is the same. 2, explosive atmosphere by pneumatic diaphragm pneumatic pumps reliable and low cost, and the third, the fluid does not overheat because the diaphragm of the fluid stirring minimum. 3, at the site where the bad, such as waste water construction sites, mines, because the sewage impurities and complicated, easy to plug the pipeline, so that the load is too high the pump to be formed, the motor heat vulnerability. Pneumatic diaphragm pump through the particles and adjustable flow stops automatically when the pipes get clogged to smooth. 4, another small pneumatic diaphragm pump easy to move, without foundation, of the ground is extremely small, easy to install and economical. It can be used as portable pumps. 5, hazardous, corrosive material handling, the diaphragm material can be completely separated from the outside world. 6, pneumatic diaphragm pumps for fluid transport relatively unstable chemical properties. Pneumatic diaphragm pump in the industrial sector are enormous, many difficult humanity can be done manually by pneumatic diaphragm accomplished indirectly ensure the safety of employees. Transactions described above is part of the information that the product rich in Suzhou City Xu coating technology, or if you are interested in this product can help in production to you and you have any questions about this product, please contact the company for further welcome to inquire 18962181065 Tsang