Sawdust granulation equipment manufacturers Hainan sawdust granulation equipment Sanli Heavy Equipment Factory Certified

Boot sequence: 1. start the main motor, etc. buck starts normally, start force feeding, open the front into fuel plates, the oil starts speed auger 2-4 minutes later, transferred to the governor auger of tuners 6HZ, look at the functioning of the raw material particles machines, such as normal operation, wait two minutes raised 8HZ, see biomass pellet machine functioning, and gradually increase to host the current value (200A-240A) not less than 180A, nor higher than 240A; 2. the operator can not free to leave the cabinet in order to keep the current adjustment, when the raw water containing high, the current pointer will change to go down, then the pointer to the current regulation, when the raw water containing relatively low, ER pointer at the meeting to go, then go down to the current, always to the current control at rated current; shutdown sequence: 1. When stopped, the first stop in the feed bin blender, then stop the governor hinges Long, and then open the feed plate plus fuel, allows the host to idle for 3-5 minutes, then turn off the forced feeder, then close the host. The sequence of operations is; the first to open after the motor off, after first opening of the motor is off. 2. boot sequence: Host - forced feeding - speed auger - feed bin blender; 3. shutdown sequence: raw materials warehouse blender - speed auger - forced feeding - host. Sanli XGJ biomass pellet machine uses a motor directly connected mode, the motor is connected via a gear coupling with the gear shaft, through reducer 90 ° change of direction, horizontal vertical hollow shaft motor drive, spindle drive pressure wheel rolling mill with the completion of the inner surface of the pressing process. In operation, the material by the pellet mill feed inlet surface perpendicular fall frame plate, frame plate rotated so that the material uniformly distributed in the mold cavity surface (pressure roller contact with the mold facade), the press wheels rolling Under powdery material through the die holes. This procedure receives material effects a high pressure, high temperature, resulting in a physical change, to promote the formation of powder material continuously elongated cylindrical solid body, and then be uniformly distributed around the die cutting knife, a certain size of particles, and finally by a dial feed tooth concentrated to the discharge port, automatically fall. Sanli XGJ biomass pellet machine Advantages 1. automatic feeding system, precise control of feeding amount, to avoid causing too much material card machine, crash phenomenon and lack of feed produced by the machine idle. 2. The vertical feed, easy to operate, reducing the machine with the link feeding time, improve the fluency of the production line. 3. ring mold does not move, roll move material around the use of centrifugal force uniform, effectively reducing the machine in the production of vibration, balancing the machine more reasonable state. The vertical structure, easy granulation chamber thermal cooling. 5. Automatic refueling, without manual operation, the effective protection of bearings to improve their life. Analysis of vertical ring mold particles granulator process stability and energy-related factors vertical ring die pellet mill because of the prepared particles good quality and high efficiency in the related field of industrial production, biomass energy industry has been widely used. At present, China's ring die pellet mill products remains poor stability, short life, higher energy shortage has seriously hampered the development of related technologies and industries. Gongyi City, Henan Sanli heavy equipment factory on the basis of analysis of relevant factors granulation process stability and energy on, high stability, low power consumption granulation technique has been studied mainly as follows: (1) The ring die pellet forming into the mold, roll and roll the die hole in the squeeze between the two processes, respectively, two of the material during the mechanical analysis, and based on grab angle and height granulation solving the factors influencing the granulation process . (2) for the ring mold die hole arrangement under existing easy-cracking problem, designed two new die hole arrangement, three ring mold and the finite element analysis results show that with the new arrangement of mold hole help to improve the strength of the ring mold. (3) analysis of the ring mold width is affected by changes in its force and strength, the results showed that with the increase in the width of the ring mold ring mold overall amount of deformation increases, the feed end easier to crack. (4) Experimental study of particle machine vibration ring mold different widths and line speed combinations, and has been the optimum combination of parameters such that minimal vibration. (5) The high rolling granulation process was simulated by changing the model parameters to explore the influence of various factors on the rolling process. The results show that with the increase of the friction coefficient and the mold roll diameter ratio is reduced, the powder material compression molding nip better quality. (6) of the die hole extrusion process was simulated to obtain the required material granulation extrusion pressure and rolling and extrusion die orifice to analyze the process together, and then put forward a pellet machine parameter optimization saving The design process.