Supply of wear-resistant non-stick fluorocarbon coating machinery and equipment parts

Anhui big bang preservative Equipment Co., Ltd. is located in Anhui Quanjiao yangqiao Industrial Park, close to the Hefei-Nanjing Expressway, the traffic is very convenient. The company is mainly engaged in fluorine resin coating, non-stick PTFE sheet tight and self-lubricating liner. The company has a modern management concepts and advanced production equipment, to complete non-stick, heat, lubrication, water and oil, the special anti-wear and anti-corrosion coating and other tasks Teflon. The company has a large production equipment, advanced detection equipment, strict production process, provide you with convenient and satisfactory service: First, raw materials are DuPont (Dupont), Whitford (Whitford), Solvay (Solvay) and Daikin (Dakin) based paint, two, Fusu spraying (1) anti-corrosion chemical equipment: filters, reactors, centrifuges, filter plates, a stirring rod, float, mixer, level gauges and other chemical accessories. (2) Chemical Machinery preservative: mainly centrifuges and dryers. (3) chemical piping, valves corrosion: suitable for a variety of chemical accessories. Third, the special industrial (1) resistance to salt spray corrosion: usually used in marine operations, oil machinery of resistance to salt spray corrosion of the workpiece. (2) anti-static spray: used in both the release, but also anti-static wear special industries, such as dryers. Fourth, the use of PTFE sheet lining the PTFE sheet lining process all types of pressure vessels, storage tanks, tank and so on. Teflon has the advantage (1) is not sticky: almost all the material is not bonded with Teflon. Thin film also shows a good non-stick properties. Use the PTFE sheet lining process all types of pressure vessels, storage tanks, tank and so on. (2) Heat resistance: Teflon has excellent heat resistance and low temperature properties. A short time can be high temperature to 300 ℃, generally between 240 ℃ ~ 260 ℃ can be used continuously, with significant thermal stability, it can work without embrittlement in freezing temperatures, it does not melt at high temperatures. (3) Teflon has a low coefficient of friction. Load sliding friction coefficient changes, but only in the values ??between 0.05-0.15. (4) anti-wet: Teflon surface above water and oil production operations are not easy to dip solution, if a small amount of dirt, simply wipe clean?. Down time and can save time and improve efficiency. (5) wear resistance: under high load, with excellent wear resistance. There is a certain load, wear-resistant and non-sticking? Dual advantages. (6) corrosion resistance: Teflon almost free from drugs erosion, to protect parts from being any kind of chemical corrosion. Teflon non-stick, wear-resistant, self-lubricating (1) rubber and plastic industry: rubber, plastic products, such as forming metal mold (shoe mold, ball mold, EVA mold, glove mold, plastic mold, styrofoam molding, Hot plywood templates, etc.). (2) Textile Industry: Textiles, leather and other mechanical guide wheel, cotton wheel, fit the wheel, wheel dyeing, sizing wheel, non-woven wheel and its components. (3) Food industry: food machinery, biscuits, bread, candy hotplate. Automotive: pistons, piston rings, throttle shaft, a joystick, a hinged pin, all kinds of bearings, brake shoe, the bearing retainer, guide seat, the mixing chamber throttle. (4) Other industries: scissors, saw, gas switch, ball valves, bicycle brake line, scrapers, copper knives, razor blades, screws, nuts and so on. Spray paint can not compete tetrafluoroethylene having other comprehensive advantages, its application flexibility makes it almost all shapes and sizes of products are used. PTFE coating temperature curing process is the key process of coating tetrafluoroethylene or bad. Deep enough to cure the coating of the low coating adhesion strength, coating easily broken off; the coating is cured too deep aging of the coating can easily break off and prone to sintering, to produce the mold shrinkage corrosion and surface change very rough cause mold scrapped. After spraying tetrafluoroethylene baking is completed, the service life of the cooling rate of speed of the coating also has some influence, because the mold shrinkage of the coating and substrate is different, so in the oven with the oven along slow cooling effect is better. Anhui big bang preservative Equipment Co., Ltd., specializing in anti-corrosion chemical equipment technology research and development and production of high-tech enterprises. I am using spray PTFE, electrostatic spraying tetrafluoroethylene, rotational lining, lined with plastic equipment, and other advanced technology, polytetrafluoroethylene (PTFE), soluble F4 (PFA spray), F40 (ETFE coating), F46 (FEP) , polyolefin (PO) for the anti-corrosion lining material, the overall shape of large, plastic-lined steel equipment and anti-corrosion lining equipment fittings. The company currently operating scope mainly spraying PTFE, PTFE sheet lining, anti-corrosion equipment, PTFE corrosion, lined equipment. We will be dedicated service, excellent quality, high reputation, they are welcome to discuss cooperation.