LED flood light advantage and product value of the light source

LED flood light is widely used in billboards, building floodlighting, tennis courts, car parks, stadiums and terminals and other places. LED floodlight advantages are obvious, but also by consumers, it was first used in task lighting, home lighting, shopping malls, supermarkets lighting and factory lighting and other places, expand the space for the majority, LED ceiling housing in practical applications We must first consider the scope of use. LED Spotlights adaptability. LED downlights time there is no doubt initiated, electricity can immediately work properly, no long wait. Light color is good, near to natural light, easy active device, adjustable to any angle, wide versatility, the use of program, the problem is the only standard light source LED ceiling housing. LED lights cast light source color rendering index higher. GB this interval CRI requirement is Ra = 60, CRI LED light source is usually higher than conventional light sources. Level at the time, LED downlight CRI can reach 70-85. Public toward LED Spotlights Product details: 1. lamps shell environmental ADC-12 aluminum die-casting; surface electrostatic spraying powder. 2.5-8mm thick high-strength tempered glass, high temperature inside the high temperature 3. Imported high-quality silicone rubber seals 4.1.2mm high thermal conductivity aluminum circuit board 5. The high thermal conductivity 1.59Wm / K thermal silica; 6. Lens: Optical Grade lens, 15 degrees, 30 degrees, 45 degrees, 60 degrees optional 7. source: 1W * 3Pcs USA Bridgelux 45mil LED chip; 8. colors: red, green, blue, white, warm white; 9. Drive: Built Constant current driver 10. Input voltage: AC86-260 V 11. Power consumption: Pw≤3W; 12. Frequency: 50 / 60Hz 13. Protection class reference value: IP65; 14. Ambient temperature: -40 ℃ to + 60 ℃ ; 15. Product Warranty: Three years Scope: LED flood light is widely used in billboards, building floodlighting, tennis courts, car parks, stadiums and terminals and other places Features: 1. Using a special lamp housing structure makes wind It can speed up the flow of the cooling effect, while reducing drag, reducing the pressure load of poles. 2. Structural waterproof features: unique structure is conducive to the discharge of water on the shell, the new waterproof silicone seal to ensure the lamp to ensure that no water and dust. 3. Superior thermal structure: radiator and light body integration, thickening of the aluminum can improve the real-time thermal; wave helical fin to increase the cooling area, effectively improve the heat dissipation effect. Heat the entire intermediate structure is superior to both sides, and thus play a uniform cooling effect, so that the whole street is more stable during use. 4. Easy installation: adjustable bracket, easy to install poles of different diameters, installation more secure. 5. Surface treatment: anodizing, electrostatic spray waterproof pad thickness of 6.0mm. 6. Material: ADC-12 die-cast aluminum, tempered glass. 7. Weight: 0.5kg. Lighting installation matters: First, the pitch and the number of lighting fixtures required is calculated as follows: 1, L1 = 2m, L2 = 2m, L3 = 2m. Height = 25 × lighting illumination distance from the wall, which is 25 times the height of the lamp is irradiated from the wall distance. 2, lighting power density requirements 1 ~ 5W / m2. = Total power lamp is irradiated surface area × (1 ~ 5). = Total number of lamps lighting power / single lamp power. Second, the installation steps: 1, the lamp base has mounting holes. 2, hold the base to the mounting location. 3, a pen or other tool to position the screws in the wall opening. 4, drilling. 5, the mounting base, the stable screws and the like. 6, adjusting screws on retaining clips, adjust lighting illumination angle to the right. 7, lamps bottom three power cords, AC POWER INPUT AC mains input connected to the AC grid. This line is 3-core wire; blue line is zero line N, brown-red line is the line of fire L, yellow / green and yellow wire is the ground wire PE. Note: 1, The light is waterproof design, the protection level can reach IP65. Can withstand rain down on the test but not immersed in underwater work, underwater work less than the protection level requirements. 2, the position of the lighting installation must have sufficient capacity, its carrying capacity should be able to withstand 10 times the weight of the drive over. 3, high voltage AC power for the lights work, away from the crowd easily accessible place, and make grounded lamps, must be grounded wire. 4, the lamp is a power-type device and is very sensitive to the ambient temperature, ambient temperature higher than 45 ° C when their life will be significantly decreased, accompanied by light fades serious signs of surface. Therefore lamps should be placed ventilated place, keeping the lamp has relatively good thermal environmental conditions. 5, lamp working temperature between -40 ° C ~ + 60 ° C. Temperature in the workplace must not exceed 45 ° C, in order to ensure lamp life. 6, the lamp power is relatively large, cloth Power cord should choose the right according to the actual power supply line. And sub-phase power supply.