Environmental bronzing pulp, pulp prices perm, Guangdong melt bronzing pulp

Cold hot paste / bronzing pulp GC-31 perm type bronzing pulp is dedicated to the transfer of special textile bronzing pulp, has excellent permeability, gentle nature, leveling, can significantly increase the strength of the coating, adhesion, washing fastness; soft, does not contain formaldehyde, environmental compliance, it is a high-tech new bronzing products. gc-31 perm pulp change the traditional way of gilding it must rely on hot way to transfer gold foil, a cold foil transfer slurry new concept, applicable to all kinds of cotton, fiber and other fabrics gold foil stamping. gc-31 perm type bronzing pulp ratio and the company must be supporting the use of special additives, cold hot syrup and additives 100: 1-100: 2, equipped with auxiliaries adhesion, wash fastness, tensile elastic effect better. Features 1, clear perm type bronzing pulp stamping patterns effects. 2, good water solubility, flat wear, noble quality show. 3, soft; has excellent compatibility, operability, not plug network. 4, do not isolate slurry can be easily perform complex pattern printing. 5, cold hot stamping applicable Pan Wai Kwong, processed faster. 6, perm type bronzing pulp can also be used in conventional hot stamping process or by backing pulp. 7. Tested: Gao brand cloth with gold and silver cold hot water temperature of 60 ℃ after use, the machine does not fade wash 60 minutes. Use 1, when GC-31-type cold hot hot hot bronzing pulp suitable for screen printing process operation. 2, when you add the GC-31 perm type bronzing pulp special additives must be taken depending on the needs of the day and then add the right amount of bronzing pulp, add over aid bronzing pulp can not fall back again within the aid was not added bronzing pulp, and it must be used up within two days, as the time to place too long, it will affect the results. Indian gold foil stamping process recommendations paste two or three dry, paved hot foil, pressing over the net, with a hard mouth spatula scraping back and forth with the empty net to make hot foil stamping paste adhesive, Tearing (multicolor bronzing Repeat the above steps), bronzing complete After the mortar can then be printed, crack pulp, flocking pulp, dry for 24 hours; or heat-treated (dryer 130 ℃ 2 minutes or pressing machine 150 ℃ 15 seconds, the dryer and Pressing Machine The company has supplied!). Note 1, not recommended to store and use the following 0 ℃, the actual operation and related test results would be affected. 2, GC-31 perm type bronzing pulp slurry find thick, add water may be appropriate to adjust the sample, do not use solid pulp. 3, GC-31 perm type bronzing pulp must be supporting the use of special additives, using now equipped with the proportion of transfer attention, and must be fully equipped with stir evenly. 4, according to different kinds of printed fabrics, thickness, permeability and stretchability, printing coating amount of binder will vary. 5. In practice, GC-31 perm type bronzing pulp products mature, stable technology, first after the bulk sample test can be re-used in order to avoid unnecessary losses are recommended based on the requirements of different fabrics. (Note: The above data for reference only, the customer shall be subject to self-testing, customers are welcome to demand model!) Products This product according to the technical requirements and equipment, the process can also choose to select perm scalding process. It has washing fastness, soft to the touch and so on. This product has been cultivated by the Japanese company's environmental assessment division, in line with the latest EU environmental standards. First, the product traits 1, Appearance: white paste ????????? 2, viscosity: 40,000 ~ 60,000cps 3, PH value:? 6-8; 4, nonionic; 5, the product at room temperature under the sealed state, the storage period of six months. Second, the use of 1, the backing slurry can not be too thin, the first India finished second track pulp dry before printing to ensure flat pattern printed surface. The second track to be slightly dry pulp can be gold, silver paper park Pressing. 2, such as using cold foil process, over the machine pressure should ensure 6-8KG. 3, such as the use of blanching process, hot paper temperature not exceeding 180 ℃, time of 10 seconds is appropriate. Pressing temperature is too high, it may lead to Kim, India Park discoloration. 4, until the fabric is completely cooled, torn gold, silver Fumo parked on a perfect bronzing effect can occur. 5. To improve product washing fastness, the proposed 2% cross-linking agent in bronzing pulp.