Rotary die-cutting machine wholesale base, rotary die-cutting machine vendors

Rotary die-cutting machine wholesale base, rotary die-cutting machine tool vendors in the study circle is a lengthy process that requires a certain period of time to gain experience, and experience is by constant practical operation, accumulation and exchange. Often occur in the production process of such problems, the more common problems and prevention:? 1. No material runs out, some machines have electric eye monitoring can be automatically shut down, common approach: calculate each material on a good machine, from less to give it more heart ranked teams. ? 2. Materials received crooked or access is not reliable, or wrong. Way: the new then, until then good shall prevail. ? 3 product contraction: reduce discharge tension or carboplatin ring fixed raw materials, without tension. ? The swap pieces: Check whether a foreign body support ring, cleaning the support ring; check if there is a problem of mold, mold repair; check whether there is foam mat knife wrapped gum is no stretch to replace foam; whether the knife to flatten new knife nip pressure. ? 5. sticky mold: replace the foam, or coupled with Teflon, silicone foam in the foam, then add from the film or the like, more complex approach may be directly open mold release coating, or Apply silicone mold cavity knife (similar to glass, plastic). ? 6 sets of position deviation or unstable way: adjust the ratio of discharge tension, new rubber nip roll flat, 7 dirty, way:?. On board before the clean machine, the production should always ensure good peripheral ?. 5S 8 excess glue, approach: reducing rubber nip roll pressure and tension income products, replace a little thin foam. ? 9. scratches: Check raw materials; check whether the lesser curvature of the rod does not rotate; check whether there is friction to the machine; check the transmission shaft or if there are special foam tape. Such as Teflon. . . . ? 10. The discharge of waste is bad, way, replace the foam; adjust the angle of the material; adjusted rate;? Of course there are many other problems and approaches, in which not one of the listed, do not approach the problem outside almost on personnel, machines, accessories, materials, process methods and environmental ...... simple rotary die-cutting machine Main performance characteristics: 1. speed up to 50 meters per minute. 2. Suitable for blank labels, simple rotary die-cutting products. 3. The low price and practical. GZ-250 round knife cutting machine (single-pole) Key Performance characteristics 1. This round knife machine speed, high efficiency. 2. Can the same time fit / discharge waste / die / fit. 3. The rotary die-cutting pressure more stable. The orders for large or stable cutting products. 5. Can replace the traditional laminating machine, a machine. Technical Specifications Model GZ250 winding shaft 4 sets of 4 sets of complex discharge axis width 250mm width 250mm die-tension control tension control independently for each axis can be both positive and negative `round knife range 60-160 gear teeth pitch speed 0-40 1/8 Adjustable Frequency meter positioning accuracy of + 0.1mm Power 220V / 1KW machine appearance 2300 * 750 * 1700 GZ-250 round knife cutting machine (pole) main performance characteristics 1 This round knife machine speed, high efficiency. 2. You can install two knives, http: //www.baidu.com/s word =% E6% A8% A1% E5% 88% 87% E6% 9C% BA & tn = 90940531_hao_pg & lm = -1?. 3. simultaneously bonding / exhausting / die / fit. The rotary die-cutting pressure more stable. 5. orders for large or stable cutting products. 6. Can replace the traditional laminating machine, a machine. Technical Specifications Model GZ250 winding shaft 4 sets of 4 sets of complex discharge axis width 250mm width 250mm die-tension control tension control independently for each axis can be both positive and negative `round knife range 60-160 gear teeth pitch speed 0-40 1/8 Adjustable Frequency meter positioning accuracy of + 0.1mm Power 220V / 1KW machine appearance 2300 * 750 * 1700 GZ-150/250 three rotary die-cutting machine three rotary die-cutting machine is for high-efficiency electronic adhesive accessories, precision machining equipment. Equipment widely used in mobile phones, digital cameras, computers and other electronic adhesive die-cut parts. The machine has a multi-layer, multi-seat die cutting, waste discharge, multiple simultaneous unwinding and rewinding, advanced technology, reasonable process, compact structure, convenient operation, high production efficiency. For different products and strong ability to adapt to technology, cutting quality and production efficiency is much higher than other die-cutting mode, is Adhesive die increase productivity, reduce operating costs of production ideal choice. To meet the different specifications of die cut products can be tailored according to die-die-cutting equipment manufacturer requirements. Technical parameters die types: rotary die; die material: non-woven, mesh, foam, single, double-sided adhesive, PET, black and white plastic, single-sided adhesive, Adhesive and other electronic Applied Materials; 1. die width: 1 ~ 150mm, 1 ~ 250mm two specifications 2. retractable roll maximum diameter: Φ400mm 3. maximum cutting speed: 50m / min (depending on the production process) 4. cutting accuracy: ± 0.1mm 5. cutting, complex station: 3 Group 6. Machine Unwinding 4 components: Winding 4 components 7. winding and Reel Specifications: Φ3 inch (air shaft) 8. round knife Gear Pitch: 1/8 "9 Machine size: 2050mm * 850mm * 1760mm 10. Weight: 600KG 11. Power Specifications: AC220V X 50HZ 3.7KW GZ-150/250 four rotary die-cutting machine four rotary die-cutting machine is for gluing electronic accessories high-efficiency, high-precision machining equipment. equipment widely used in mobile phones, digital cameras, computers and other electronic accessories adhesive die-cutting. This machine has a multi-layer, multi-seat die cutting, waste discharge, multiple simultaneous unwinding and rewinding advanced technology, reasonable process, compact structure, convenient operation, high production efficiency. for different products and strong ability to adapt to technology, cutting quality and production efficiency is much higher than other die-cut way to increase capacity is to die Adhesive productivity, reduce operating costs of the ideal choice to adapt to different product specifications die, die-cutting equipment can be tailored according to the requirements of manufacturers technical parameters die die types: rotary die; die material: No woven fabric, mesh, foam, single, double-sided adhesive, PET, black and white plastic, single-sided adhesive, and other electronic applications Adhesive materials; 1. die width: 1 ~ 150mm, 1 ~ 250mm two specifications 2. retractable roll maximum diameter: Φ400mm 3. maximum cutting speed: 50m / min (depending on the production process) 4. cutting accuracy: ± 0.1mm 5. die, complex stations: 4 Group 6. Machine Unwinding 5 components: Winding 5 assembly 7. winding and Reel Specifications: Φ3 inch (air shaft) 8. round knife gear pitch: 1/8 "9 Machine size: 2370mm * 980mm * 1760mm 10. Weight: 700KG 11. Power Specifications: AC220V X 50HZ 4.9KW