Brands of imported belt

Hai Wen spin Electrical Equipment Co. is a professional agents operating world-renowned brand of industrial belt. Belt belt categories include: Samsung Japan (MITSUBOSHI), Bando (BANDO), Germany Obi (OPTI), (BRECO), (CONTITECH), the United States Gates (GATES), Italy Mr Gaudi (MEGADYNE), Israel (VECTOR POWER), Fujitsu (FUJI), Japan Matsuda (SONTIAN), Taiwan Mountain brand (MOUNTAINROPE) (TOKUROPE), Dongguk a (DONGIL) and so on. Belt Model: trapezoidal tooth belt MXL, XL, L, H, XH, XXH, T2.5, T5, T10, T20, AT5, AT10, AT20, arc tooth belt 3M, 5M, 8M, 14M, 20M , S2M, S3M, S4.5M, S5M, S8M, S14M, S20M, RPP3M, RPP5M, RPP8M, RPP14M sided tooth belt DXL, DL, DH, DXH, TP5M, TP8M, TP14, precise arc tooth belt 1.5 GT, 2GT, 3GT, 5GT, High Torque Timing 8MGT, 14MGT, ensure strong belt 8MGT2,14MGT2, belt common problems and solutions to problems Symptom Cause Solution bandedge excessive wear a pulley is not parallel; 2, bearing parts of the rigidity enough; 3, ring bending; 4 ring surface roughness, 5, with touch protective shield or stent transmission. 1. Adjust parallelism; 2, increased stiffness, indeed fixed; 34, amend or replace the ring; 5, check the protective shield or stand. Toothed excessive wear an overload; 2. preload is too large; 3, the tooth surface roughness; 4, severe pulley runout; 5, dust or sand; 6, shake violently; 7, too much dirt falls within the drive unit. 1. Check the design, choosing the right bandwidths; 2, adjust the appropriate pre-tension; 3, check and adjust the surface roughness; 4, check and adjust the radial runout; 5, to avoid debris mixed; 6, structural adjustment or minus shock device; 7, to clean the dirt. Toothed cut 1, overload or excessive shock loads; 2, the number of teeth together too small to 6 or a multiple of the number of teeth with teeth; (3) preload is too small; 4, the pulley diameter is too small; 5, Environment temperature is too high or other debris falling oil; 6, by accident stopped, sudden load increase. 1. Check the design; 2, check design, with an odd number of teeth; 3, adjust the preload; 4, increasing the pulley diameter; 5, change the ambient temperature, use a protective cover; 6, unexpected inspection equipment, placed recurrence accident. With longitudinal 1 with Ran pulley; 2, with a deviation to the ring; 3, when installed with a cut on the ring. 1. Adjust parallelism; 2, adjust the parallelism, check ring; 3, Installation. 1 belt elongation, bearing not reliable fixed center distance run smaller; 2, with a tensile layer loose; 3, the tension wheel loose; 4, pulley wear; 5, overload. 1, note that the design of the installation or improvement of the structure; 2, replace the belt; 3, check the tension wheel, the installation attention; 4, replace the pulley; 5, check design, changing bandwidth. Cracks or belt with the back soften ambient temperature is too high ambient temperature change operation noise is too large 1, overload; 2, preload is too large; 3, the pulley is not parallel; 4, the pulley diameter is smaller than the bandwidth; 5, belt and belt round malocclusion. 1. Check the design; 2, adjust the preload; 3, adjust the parallelism, the installation calibration; 4, check the design; 5, check the belt and pulley.