The best cable stripping machine which brand

Tandem brand TB-20 type of scrap cable stripping machine detailed parameters: Scope diameter 1.5-32mm voltage 220-380V power 1.5kw Dimensions 530x520x830mm efficiency 30-50kg / h Weight 60kg Name: dual-channel stripping machine forward (11 material well) Scope: Diameter 38mm diameter 1.5mm- size: 530 × 520 × 830mm Weight: 60kg Voltage Power: 220 / 1.5kw 220v / 2.2kw 380v / 1.5kw number of production days: 100kg-300kg Functions and Features: This stripping machine The operation and structure of the most simple, is also convenient, single-wire copper cable can be rolled processing (agent pressure) or with a blade to break open, the other cable must be with a blade to break open an insulating layer, and then remove the copper wire. Scrap cable wire stripping machine, start the motor, check functioning properly, the feed view the size of the file Outsourcing rubber cable diameter, followed by root feeding. 2, in order to be able to insert long-term durability, should feed the rubber cable connector cut, in order to avoid chipping blade gap. 3. If, after feeding it appears too deep and yarn breakage, pay attention to the following conditions: ①, should adjust the feed file that is on both sides of the blade Axis M12 screw pressure tightness; ②, in the feed to check whether the location misplaced ; ③, is new for the blade, cutting edge is too sharp, the application-specific Whetstone little trim, modest so far. 4, if the feed out later, rubber has been stripped, but copper can not spit. There are four points situation: ①, the shaft knurled too deep, application-specific Whetstone will be grinding on the shaft, but not too much grinding, grinding likely to cause too much oily hard drive cables; ②, spring pressure is too loose, you should tighten the pressure, can spit lasts; ③, wire diameter is too small, or the vertical axis gaps ones, should be raised to two-axis clearance 0 .4 --- 0 .6mm; ④, processing Rubber cable has fever, copper can not spit. 5, if the feed pressure profile agent can not drive past the cable, expected to stay in the middle, the case appeared in the following situations: 1. Check the file if there is slack in the belt; 2, check the pressure on both sides of the spring pressure profile if too tight, not the top power, should relax the pressure; ③, cable oil too much, so that the two shaft slipping, should always be two shafts dry, (when dry, if the machine in operation, please pay attention to safety) 2. Product ID: 002 Model: TB-002 (double roller automatic separation of cable stripping machine) Details Name: dual-channel cable stripping machine "new rapid automatic separation Cable Stripping Machine" Technical Data Processing range: Φ1mm --- Φ32mm Machine dimensions: length X width X thickness of 54cm * 52cm * 84cm Weight: 81kg Motor power: 1500w motor voltage:. 220v 380v .110v 10 hrs / Yield: 100kg-300kg Function: This machine is suitable for all types of wire, monofilament and Prose wire cable to achieve automatic separation effect, is widely spoken dismantling industry stripping equipment. Instructions: 1, start the motor, check functioning properly, the feed view the size of the file Outsourcing rubber cable diameter, followed by root feeding. 2, in order to be able to insert long-term durability, should feed the rubber cable connector cut, in order to avoid chipping blade gap. 3. If, after feeding it appears too deep and yarn breakage, pay attention to the following conditions: ①, should adjust the feed file that is on both sides of the blade Axis M12 screw pressure tightness; ②, in the feed to check whether the location misplaced ; ③, is new for the blade, cutting edge is too sharp, the application-specific Whetstone little trim, modest so far. 4, if the feed out later, rubber has been stripped, but copper can not spit. There are four points situation: ①, the shaft knurled too deep, application-specific Whetstone will be grinding on the shaft, but not too much grinding, grinding likely to cause too much oily hard drive cables; ②, spring pressure is too loose, you should tighten the pressure, can spit lasts; ③, wire diameter is too small, or the vertical axis gaps ones, should be raised to two-axis clearance 0 4 --- 0 6mm;.. ④, processing Rubber cable has fever, copper can not spit. 5, if the feed pressure profile agent can not drive past the cable, expected to stay in the middle, the case appeared in the following situations: ①, check the file if there is slack in the belt; ②, check the stalls on both sides of the spring pressure if too tight, not the top power, should relax the pressure; ③, cable oil too much, so that the two shaft slipping, should always be two shafts dry, (when dry, if the machine in operation, please pay attention to safety)