Coating machine

First, the use and features: Rotary coated machine equipment by a screw conveyor, mixing tank, pump, hosting, and powder talcum powder or liquid coating process components. Can effectively prevent caking of compound fertilizer. Polypropylene or acid stainless steel lining inside the host. The device according to the technical requirements of the internal structure to do a special design, is an effective fertilizer special equipment. Second, the principle: Rotary envelope machine its working principle is: the main motor drive belt and pulley, through reducer drive to the drive shaft, by installing a split gear and drive shaft large teeth fixed on the body ring with teeth together, facing work. Material from the feed end to join, the interior of the cylinder. So that the air flow inside the cylinder to accelerate under the induced draft fan (with the machine supporting the use of) suction. Third, the structure outlined: 1. carriage parts: the whole body by the rotating part of the support bracket, a larger force. Roller frame so the machine parts are made of carbon steel plate, channel steel welded together, and passed the strict quality control and special process requirements, has the purpose of this machine is used. In addition In addition more important is fixed on the shelf roller, with due consideration to their body roll band will have a greater friction, I plant specially selected high-quality anti-corrosion, wear-resistant materials, greatly improving the life of the machine, roller one frame also by casting technology. Another four corners in the roller frame lifting hook for easy handling and transportation. 2. Transmission parts: the entire transmission granulator is particularly important part of the work the entire body thus the line. Transmission channel frame are made of high quality welded and adopted strict quality requirements. The main motor and gear rack mounted on the drive are selected ISO national free products, reliable quality. Motor driven pulley, belt, gear drive to the spindle, so that the body of work, which work with the spindle drive gear parts, nylon pin coupling engageable transfer drive. 3, ring gear: fixed to the body, and the drive pinion gear together, driven toward the body work, the use of high wear-resistant materials, so that the machine last longer. 4, roll band: fixed on both sides of the body, in order to support the entire body. 5, parts of the body: the entire coating machine is the most important parts of the body, in its high-quality carbon steel plate welded together, and through strict quality control and the specific process requirements, to achieve the purpose of the machine is used. Fourth, the technical parameters: Specifications power production capacity of the inner diameter of the cylinder length tilt speed Mm mm mm (°) r / min t / h kw BM1200 × 4000 1200 4000 3 14 ~ 5 5.5 BM1400 × 4000 1400 4000 13 ~ 7 7.5 BM1600 × 6000 1600 6000 12 ~ 15 11 BM1800 × 8000 1800 8000 12 ~ 30 15 V. Installation and commissioning: 1, the installation: the machine back to the factory, and with the installation process, pointed elevation and horizontal position, tilt installation, the general inclination 2-5 degrees (allows users to adjust), the machine frame and drive bays are foot hole, can be installed on concrete. 1>. Machinery and between each base and the base pad into the Qi-shaped plate thickness should not exceed 30-35mm;. 2> Qi-shaped plate adjusting the height of each of the respective base chassis tilt 5 degrees; 3> after the appropriate adjustments each base The drum is laid on the stand, and the final adjustment roller; transmission parts 4> Install envelope machines; 5> after really trust wheel, gear, cylinder adjust the right start pouring cement, after 8-10 days, and cement. After solidification start load test; 6> body position adjustment method:. a full length in the right and left sides of the body, put two parallel wires, the wire diameter is 0.5-1mm, and with the level meter to check the wire. level; b sides along the dryer from each rounded down two and rounded tangent with hammer;.. c Measure the distance from the wire to fall between the lines to detect the body in a horizontal position; d measuring two. rounded the highest point relative to the vertical elevation to check the position of the body in a vertical plane; e mobile roller approach used to tune c, d two of the determination, so that the body in the correct position; 2. load test: 1> . 8 hours uninterrupted load, each bearing temperature should rise steadily, while test termination bearing temperature not higher than 50 ° C; 2>. Noise gear should be uniform, not the peaks and valleys; 3>. After commissioning observe the bearing may not have serious wear and abrasion and so on. VI Handling Precautions: 1. coating machine operation, prohibit drill body below; 2. coating machine in operation, prohibit internal inspection and repair; 3. coating machine running, remove the protective device is prohibited; 4. Not with insulated gloves, Do not touch the motor and wires; 5. There is no perfect grounding wire, prohibit start coating machine, if found should immediately stop the current equipment until repaired until the ground; 6. Check the stove and packages When the film machine, prohibit the use of mobile lamp voltage higher than 12 volts.