Jiangnan Electric basket hoist manufacturers

What issues build process electric basket of need to pay attention? 1. Required basket and cantilever beam coupled with a rope entangled cantilever beam of not less than three times, can not tie clasp, three above the level required by the flow. 2. Support foot plate lateral extent pole distance: When adopting 3cm thick slate, should not exceed 50cm, can not probe springboard and securely latched. 3. hanging basket cantilever beam, length and pick the length of the ratio should be greater than its fulcrum within 3. And the cantilever beam should be high in low outside. The hanger was coupled with the construction of the necessary strong shall not swing, hanger to set the level of the flow channel. And 5. The outer ends of the basket should be located two fence panels, hanging over the level of not less than 1.5m and not less than 18cm of trawl gear or feet. 6. hanging basket cantilever beam required flow strong, usable and roof embedded anchor member Liquid flow, pressure prison adapter can also be used. But must hand lever foot cantilever beam even for all, there is the flow of containers adapter (sand bags, cages, boxes) Holds. 7. basket set single, two-storey, each level is not greater than 2m, and the increase is not greater than 1m. 8. hanger located inside the construction material for the 10-20cm, shall not be greater than the distance between the two baskets of 20cm. 9. accurate use rest cover necessities, fasten your seat belt height work. 10. Insurance operations strictly abide by the regulations, are not allowed to work or drink illegal work. Jin Ma Libang Electric basket professional-quality, durable. When electric basket construction problems encountered in the construction of emergency, in case of the following exceptional circumstances, should remain calm, and to take appropriate emergency measures l, construction sudden power outage ??? construction sudden power outage, immediately turn off the electrical box power switch, to prevent accidents while power transmission until after receiving notification of the call on the power switch and start working after the examination was normal. ??? As needed when returning to the ground after a power outage, while lifting both ends should boost Manual toboggan handle electromechanical machine that suspension platform free skate to the ground. 2, the suspension platform lift can not stop the process after you release the button down. ? When the suspended platform in the ascending, descending process, such as after the release button can not stop, immediately press the red electrical box door emergency stop switch so that the suspension platform emergency stop. Then cut off the electric box power switch, check the contactor, the adhesion of grease to clean the contact surface impurities, hands on the contacts can be restored to normal operation, close the power switch, emergency stop switch so that rotating back into place to continue working after . Such as the fault persists, you should cut off the power switch, use the manual method to suspension platform downhill to the ground for maintenance. 3, safety locks should be at work in the open, in a working state automatically, without manual operation. Its role is to enhance the system failure as a result of speeding basket drops to automatically lock the safety rope so that the gondola stop the descent of man and machine safety. When troubleshooting, when you need to re-open the security lock, you should first move the basket to rise, so that the safety lock a little loose, before flipping open the lever to open the safe lock. Prohibited under safe circumstances rope taut, hard pulled open the handle, so as not to damage the safety lock. Do not operate the machine after the safety lock Locking hoist fell so easily cause serious damage. 4, the working steel Sishengyinsong shares, kinked or damaged hoist another piece jam in the hoist rope jammed in the work when lifting the machine should be shut down immediately. Non repeatedly raising and lowering forcible relief. In ensuring the safety of the evacuation of construction workers suspended within the platform, sending specially trained maintenance personnel into the suspension platform maintenance. First, the safety rope wrapped around both ends of the hoist mounting bracket with a tie clip to fasten safety rope ends. Then release two security lock arm roller guard ring (see Figure E), will work with the rope rollers disengaged, so that the two ends of the rope lock in lock state. After taking the above safety measures and remove hoist inspection, and exit the jammed rope, wire rope failure may be necessary is cut off and lift the chassis cover open for inspection, and carefully remove the wire rope hoist to stay in. While the corresponding position in the suspension mechanism replaced with a new rope, the rope again for a good man down and wear the machine up to tighten the rope, and then the work rope loaded safety lock arm roller slot, install the protective ring so After the security lock is opened, the suspension platform upgrade about 0.5 meters to stop, take Stopper safety rope and the safety wire rope on the discharge to the overhanging position, then suspended platform down to the ground, through the hoist rigorous inspection, maintenance except after Fang allowed to continue to use. 5, when the rope breaking work ??? suspended work at one end of the rope breaking platform, suspended platform tilted, inclined to a certain position safety lock automatically when closed, will be locked in a safe rope suspension platform. At this time, the suspension platform construction should remain calm, non-electric running and jumping in a basket suspended, according to the work rope jammed the lifting of emergency measures in the machine for processing. Jin Ma Libang Electric basket professional-quality, durable. ?