Zhengzhou Zhengzhou enamel enamel condenser condenser Factory quality factory option Furun Cheung

Zhengzhou Zhengzhou enamel enamel condenser condenser Factory quality factory option Zhengzhou Furun Furun Xiang Xiang Chemical Machinery Co., Ltd. Jiajing Li: 139-3857-1642 Henan Province is the first production run of mechanical products. Major production and marketing: enamel reactor, enamel reaction cans, coolers enamel, ceramic condensers, centrifuges, Tang Boli disc condenser series. The main products are enamel reactor, enamel reaction tank, glass-lined reactor, ceramic condensers, acid pump, acid ceramic mortar pump, acid ceramic vacuum pump, corrosion resistant mortar pump, the three-foot artificial discharge centrifuge, screw discharge screen centrifuge and other equipment, and to undertake complete sets of chemical installation works. The Company observance of good faith, the principle of user-oriented, high quality, efficient, dedicated service to all users, and dedication to the development of China's anti-corrosion cause progressive. Enamel chip condenser performance characteristics: 1, glass-lined disc type Condenser points P1 and P0.5-type models. P0.5 type condensation area, each 0.5 meters, equipment outer diameter of 700mm. P1 type, each condensed to one square meter, the equipment at a diameter of 960mm. Setting specifications for 1.5-15 m2 series, condensation can be selected according to the desired amount. 2, small size, light weight and compact structure. A condensed area of ??10 square feet of glass-lined sheet P1 type condenser, only 960 kg. 3, the hot air is condensed by hot air and cooling water flows reverse exchange. Small and uniform spacing; media repeatedly spread, will merge to effectively improve the efficiency of condensation and eliminating airflow leakage phenomenon. Under normal circumstances can be used to tap water as condensate can achieve good condensation effect. The cooling water may be necessary also greatly improve access to the hierarchical parallel condensing efficiency. 4, the device in the same area of ??the condensing efficiency condenser glass-lined sleeve, graphite heat exchanger comparison, can increase 1-2 times. 5, after a certain period of use, such as the occurrence of component damage, partial replacement or reduction can be monolithic, will not cause the machine scrapped or discontinued. Greatly extend machine life. Enamel chip condenser for use: 1. enamel disc condenser to bottom, cover and a number of films, gaskets supplemented, long bolts assembled, drawings and relevant requirements should be assembled, tighten the nut should be symmetrical even by force gradually, reaching no leakage as the standard, the force should not be too tight. 2. The hot air flowing into the cover portion jack, jack out of the bottom of the condensate. Taken over into the cooling water from the bottom, the lid portion takeover outflow. According to the temperature of the outlet water temperature and the overflow of the condensate to regulate the flow of cooling water, in order to further improve the condensing efficiency. The cooling water should be controlled at neutral PH value, not less than generally between 6-8, otherwise Tiedan to be adsorbed hydrogen, can cause enamel coating peeling off a large area of ??water quality should be relatively clean to prevent deposition of impurities. 4. In the event of the use of local leakage, may be appropriate to tighten the parts of the nuts, but not too tight. 5. In use, the cooling water should first pass after pass hot air, termination should be used to stop the hot air, after the cessation of cooling water. 6. The non-rigid material glass-lined face collision, friction, to prevent damage to the glass-lined surface. 7. condensing efficiency of the product, significantly higher than the same area of ??the sleeve condensate cooler, this product should be vertical mounted vertically, not horizontally mounted and destroy the hot air flow. 8. The glass-lined thermal shock resistance ≤120 ℃, should initially introduced into the hot air pressure and temperature control requirements for slow warming, and allow the device to adapt (condensate outlet water temperature and hot air inlet temperature difference ≤110 ℃) and then to increase traffic into normal production. 9. When the condenser used for a long time, found that cooling water turbidity significantly affect the efficiency of condensation, may take measures to remove the mezzanine scale, scale removal should monolithic short pass into a 5% concentration of warm sulfuric acid, immediately after three minutes exclude acid, and then rinse with plenty of water with 0.5% concentration of dilute lye, and fully remove residual acid, should prevent Tiedan adsorbed hydrogen. 10. The condenser gasket added steel wire, can be used to direct air production system. 11. When the temperature chosen neoprene washers outsourcing tetrafluoroethane at 20 ℃ -150 ℃. When the temperature at 150 ℃ -200 ℃ when the first outsourcing tetrafluoroethylene with a fluorine rubber gasket.